California Instruments 12000L-1P Скачать руководство пользователя | Manualshive

Страница: 39 / 151

background image

INSTRUCTIONAL MANUAL

2750L-P/4500L-P/6000L-P

August, 2001

Rev. K

-35-

NO SCREEN

NAME

EXTENSIONS

ARGUMENT

ACTION TAKEN

16

CFG

A(LSN)

0-30

Sets the IEEE-488 (GPIB) Listen Address

B(CFG) *28

Defines the features enabled for Power Source
compatibility.

C(PHZ) *120

Defines the phase C initial value for power
system configuration.

17

ALM

A(RNG)

0

Code that defines the default voltage range.

B(LLM)

*135

Defines the upper limit of the lower voltage
range

C(HLM) *270

Defines the upper limit of the higher voltage
range.

18

FLM

A(FRQ)

60

Defines the default frequency.

B(LLM)

*45

Defines the low frequency limit.

C(HLM) *5000

Defines

the high frequency limit.

19 CLM A(RNG) Max

Current

Defines

the maximum current limit value.

B(PRS) *0

Defines the decimal point location for measured
power.

C(CRS) *2

Defines the decimal point location for measured
current.

29

INI

A(AMP)

0-5

Defines default voltage.

C(CRL)

0 - Max Current

Defines the default Current Limit.

*NOT USER PROGRAMMABLE. THE VALUES SHOWN ARE FOR A STANDARD 3-PHASE SYSTEM.

Table 3-8

CONFIGURATION SCREENS

3.5.3

TO PROGRAM OUTPUT VOLTAGE AMPLITUDE (AMP=5)

NOTE

The external sense lines must be connected to J6 on the rear panel of the
AC Power System. If they are not properly connected an AMP FAULT
message will result when the output relay is closed. Refer to Figure 2-3.

The output voltage Amplitude may be programmed independently or simultaneously for each phase.

Select the Amplitude (AMP) screen by entering keystrokes:

5

ENT

«
...
37
38
39
40
41
...
»

Содержание 12000L-1P
























































































































































Отзывы:

Нет отзывов

Похожие инструкции для 12000L-1P

Бренд: Laser Страницы: 8

Universal Notebook Power Supply

Бренд: Hama Страницы: 24

Бренд: Laser Страницы: 2

Бренд: F.F. Group Страницы: 36

Color Block PSU-05B

Бренд: Chroma Страницы: 2

Бренд: National Instruments Страницы: 18

MINI CARVER MIN.FG.600.60

Бренд: Arbortech Страницы: 76

Бренд: Parkside Страницы: 134

Бренд: Grizzly Страницы: 2

Бренд: Yamato Страницы: 14

Бренд: Kärcher Страницы: 68

Бренд: Dixon Automatic Tool Страницы: 11

Бренд: Far Tools Страницы: 52

Бренд: Kaindl Страницы: 9

Бренд: jobmate Страницы: 16

Бренд: FTI Страницы: 9

Бренд: KRAUSMANN Страницы: 20

Бренд: Echo Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды