Calex CMM17 Скачать руководство пользователя страница 16

6-1

Parts

Cause

Diagnosis

Remedy

Fuse blows

Defective primary

Check continuity of the primary switch terminals with

Replace the primary

out when

interlock switch

wire removed using a multimeter. If there is continuity

interlock switch

door is

ary winding.

between switch terminals when door is opened,

opened.

the switch is defective.

Defective interlock 

Check continuity of the monitor switch terminals

Replace the interlock

monitor switch

with wire removed by using a multimeter.

monitor switch

If there is continuity between switch terminals
when the door is closed, the switch is defective.

Fuse is

Layer short of the

The fuse will not blow right away, but if it blows in a

Replace H. V. Transformer

open.

secondary coil of

few seconds, then there is a layer short.

H. V. Transformer

If the fuse blows with H. V. Trans secondary open, the
transformer may be faulty.

1) Fuse blown out

Check fuse.

Replace the fuse.

2) Poor contact of

Check continuity of power supply cord. Also check

Adjust or replace the

power cord

whether the power cord is securely wired.

power supply cord.

3) Defective lamp

The fan motor rotates, but lamp does not light.

Replace the lamp.

Oven lamp

4) Defective timer

Check the terminals of timer for continuity,

Replace the timer.

does not

contacts

turning the timer knob ON and OFF repeatedly.

light.

5) Thermal cutout

In this case the oven lamp and fan do not

Replace the

S/W open

turn on

thermal cutout S/W

1) Defective

If 220~230V is found at motor terminals, the motor

Replace the motor.

Fan does

fan motor.

should be replaced.

not operate.

2) Defective con-

The oven lamp does not light and fan motor

Replace the timer.

tacts of timer

does not operate.

NOTE

Interlock monitor switch must be replaced when the fuse is blown out.

WARNING FOR HIGH VOLTAGE

4000 VOLTS EXIST AT THE HIGH VOLTAGE AREA. DO NOT OPERATE THE OVEN WITH CABINET PARTS REMOVED. DO NOT
REMOVE THE CABINET PARTS IF THE POWER SUPPLY CORD IS PLUGGED IN THE WALL OUTLET. UNPLUG THE POWER CORD
BEFORE SERVICING.

6-1 Electrical Malfunction

6. Troubleshooting

Содержание CMM17
























Отзывы: