CALEFFI SATK32107 Series Скачать руководство пользователя страница 1 | Manualshive

Страница: 1 / 24

CALEFFI SATK32107 Series Скачать руководство пользователя страница 1

H0003193.04

www.caleffi.com

SATK series wall-mounted indirect Heat Interface Unit

SATK32 series

INSTRUCTIONS FOR INSTALLATION, COMMISSIONING AND MAINTENANCE

CONTENTS

Function

The SATK series HIU allows independent control of heat regulation and
domestic hot water production within centralised heating systems or systems
served by district heating networks.
The heat interface unit features exceptional flexibility of installation and remote
controllable smart electronic functions designed to enhance efficiency of the
system.

Heating function

12

Remote user interface quick guide

10

Commissioning

9

Electrical installation

8

Hydraulic installation

5

Hydraulic components and diagram

4

Dimensions - Technical specifications

3

Safety instructions

2

DHW function - Comfort functions

Primary flow rate limitation

Circulator - curves and setting

Auxiliary microswitch

Modbus

Safety and alarms

Electronic circuit board

Periodic maintenance

Troubleshooting

Commissioning check-list

20

19

18

17

16

15

14

13

24

22

Product range

SATK32103

Indirect wall-mounted HIU for instantaneous
domestic hot water production, capacity 50 kW

(1)

.

SATK32105

Indirect wall-mounted HIU for instantaneous
domestic hot water production, capacity 60 kW

(1)

.

SATK32107

Indirect wall-mounted HIU for instantaneous

domestic hot water production, for low temperature

heating networks.

(1)

Primary side head > 50 kPa, primary flow temperature 70 °C,

DHW 10 - 50 °C

Anti-legionella function

14

All languages are available on:

IT

FR
NL

1
2
3
...
»

Содержание SATK32107 Series

























Отзывы:

Нет отзывов