20
OPERATING INSTRUCTIONS
TEMPERATURE LOCK
The Temperature Lock feature deactivates the temperature control function from the control panel. All other functions on the control panel will
operate normally. Temperature Lock is most often used by those who do not want others to change the set temperature of the spa water.
To activate the Temperature Lock, press “SET” “TEMP
▲
” button and hold for three seconds until lock symbol is illuminated.
To deactivate the Temperature Lock, press “SET” “TEMP
▲
” button and hold for three seconds until the lock symbol is no longer illuminated.
MAIN CONTROL PANEL BUTTONS AND DISPLAY
Your spa control panel is illuminated with a Light Emitting Diode (LED) and uses convenient push buttons that allow you to set the water temperature as well as the
hydrotherapy jets and mood lighting.
DISPLAY INVERSION
You may invert the main, four-digit display for easier viewing from inside the spa. Press and hold the “SET” button for three seconds until the display is inverted. Press
and hold the “SET” button for three seconds a second time to invert the four-digit display back to its original position.
TEMPERATURE CONTROL
The set temperature range is from 80°F (27°C) to 104°F (40°C). The set temperature of the spa water will automatically be 102°F (39°C) the first
time power is applied. This is the setting programmed at the factory. After the spa has been set up and used, the last temperature value set by the
user will be stored in memory. If power is disconnected from the spa, it will automatically revert to the last set temperature when power is
reapplied. (Temperatures of any setting may rise slightly depending on the current use and condition of your spa, and on outside temperature.)
To display the set temperature of the spa, press the “TEMP
▲
“ or “TEMP
▼
“ button. The set temperature will be displayed, unless the spa is locked (in which case the
word SPA is displayed with the lock symbol). The set temperature display will automatically return to actual temperature after five seconds.To increase the set
temperature of the spa water, press the “TEMP
▲
“ button. Each time the button is pressed, the set temperature display will increase by one degree. If the button is
held down, the set temperature display will increase by one degree every half-second.
To decrease the set temperature of the spa water, press the “TEMP
▼
“ Each time the button is pressed, the set temperature display will decrease by one degree. If
the button is held down, the set temperature display will decrease by one degree every half-second.
If the set temperature value will not change, check the TEMP LOCK and SPA LOCK features. When either of these features are applied, the temperature control is disabled.
JETS BUTTON
Your spa model uses one, or two buttons which affect the jet pump(s):
The “JETS 1” (“JETS” for Kauai
®
) button activates jet pump 1. When the “JETS 1” button is pressed, the jets symbol will illuminate on the control
panel display. The symbol will remain lit until the button is pressed to turn off jet pump 1, or after one hour of continuous operation when the pump
automatically shuts off.
The “JETS 2” button (used on Moorea
™
, Hawaiian and Martinique
®
) activates jet pump 2. On the Moorea, “JETS 2” also activates the cascading waterfall feature.
When the “JETS 2” button is pressed, the jets symbol will illuminate on the control panel display. The symbol will remain lit until the button is pressed to turn off jet
pump 2, or after one hour of continuous operation when the pump automatically shuts off.
MANUAL CLEAN CYCLE
The “CLEAN” button has been provided as a convenient timer for water maintenance. When the “CLEAN” button is pressed, jet pump 1 will activate. The jet pump
symbol will flash on and off until the cleaning cycle is complete. The total cleaning cycle time is ten minutes. If the clean cycle does not engage, make sure the SPA
LOCK is deactivated. SPA LOCK disables the controls on the control panel.
AUTOMATIC CLEAN CONTROL
The automatic clean cycle operates in the following manner:
• The air blower activates for one minute (except Martinique
®
and Kauai
®
)
• Jet pump 2 runs for one minute (except Kauai)
• Jet pump 1 runs for between eight and ten minutes, depending on your spa model.
This system is initiated five minutes after the spa is powered up, then once every 24 hours.
Press the “SET” + “CLEAN” button simultaneously to reset the 24 hour cycle time.
AIR JETS BUTTON
The “AIR” button activates the air blower (not available on the Martinique and Kauai ). When the “AIR” button is pressed, the air symbol will
illuminate on the control panel display. The symbol will remain lit until the button is pressed to turn off the air blower, or after 15 minutes when the
blower automatically shuts off. While the air blower is on, air only jets are operating throughout the spa. To stop the air blower when active, simply
press the “AIR” button.
