Cal Spas 2008 Gazebos Скачать руководство пользователя страница 3

2008 Gazebo Owner’s Manual 

Page 1

LTR20081011, Rev. A

Delivery and Set-up

Consider Your Privacy 

In a cold weather climate, bare trees won’t provide much 

privacy.  Think  of  your  gazebos  surroundings  during 

all  seasons  to  determine  your  best  privacy  options. 

Consider the view of your neighbors as well, when you 

plan the location of your gazebo.

Provide A View With Your Gazebo 

Think about the direction you will be facing when sitting 

in your gazebo. Do you have a special landscaped area 

in your yard that you find enjoyable? Perhaps there is 

an area that catches a soothing breeze during the day 

and lovely sunset in the evening. Consider these things 

when you plan your location.

Assembly Basics

The following will tell you how to assembly your gazebo. 

If you have any questions, problems with material and/or 

parts, contact your local retailer.

NOTE:

 It is strongly advised that you have a licensed 

professional install the foundation for your new gazebo. It 

is imperative that the foundation is level, as any damage 

that occurs due to an uneven foundation is not covered 

by the warranty.
When assembling the gazebo, the owner must determine 

what is the gazebo going to cover. If you plan to use it 

as  a  cover  for  patio  furniture,  then  you  can  place  the 

gazebo wherever you want it.
If the gazebo is going to cover a spa, we recommend that 

the spa be located in the center of the slab (for weight 

distribution) with the gazebo main supports mounted to 

the concrete at each of the four corners.

Prior to delivery of your new Cal Spa, we recommend 

that you determine where your spa will be placed. For 

example: if you are going to center your spa on the 

concrete slab, take measurements that will enable 

you to determine where the edges of the spa will be 

located. When done, mark the corner locations.)
Upon  delivery  of  your  new  Cal  Spa,  notify  the 

installation  crew  that  you  have  determined  where 

you want the spa located. 
After  the  spa  has  been  installed  and  is  operating, 

the assembly of the your new gazebo may begin.

Important: This gazebo is a free-standing unit. As with 

any structure, it is critical that all the main support posts 

be plumb (vertically level). If the first main support post 

is not plumb, then the entire gazebo will be misaligned. 

The best way to keep the structure level is to use a level 

1.

2.

3.

Delivery and Set-up

General Safety Precautions

Carefully read and follow all safety 

instructions .

When  installing  and  assembling  your  gazebo,  it  is 

recommended that two or  more people be involved. 
Do not use the unit during an electrical storm.
Do not climb on top of the gazebo. While the gazebo is 

made out of high-quality wood and is extremely durable, 

it is not meant to support weight. In addition, falling off 

of the gazebo while climbing on it can result in serious 

injury or death.
Do  not  attempt  any  repair  without  consulting  the 

manufacturer  first.  Unauthorized  repairs  will  void  the 

manufacturer’s warranty (within the first 90 days).

Delivery and Set-Up

Your  Cal  Enclosures  retailer  can  help  you  with 

foundations  and  more.  Your  retailer  has  a  wealth  of 

information and experience about how to get the most 

out of your gazebo. Your gazebo retailer also has a full 

line of accessories that are engineered to compliment 

your gazebo.

Planning the Best Location for 

Your Gazebo

Most  cities  and  counties  require  permits  for  exterior 

construction  and  electrical  circuits.  In  addition,  some 

communities  have  codes  requiring  residential  barriers 

such as fencing and/or self-closing gates on property to 

prevent unsupervised access to the property by children 

under the age of five. Your dealer can provide information 

on  which  permits  may  be  required  and  how  to  obtain 

them prior to the delivery of your equipment.
The following are some of the things that you will need to 

consider when determining the placement of your new 

gazebo.

Consider How You Will Use Your Gazebo

How  you  intend  to  use  your  gazebo  will  help  you 

determine  where  you  should  position  it.  For  example, 

will you use your gazebo for recreational purposes? If 

your gazebo is mainly used for family functions, be sure 

to leave plenty of room around it for activity.

Содержание 2008 Gazebos





















































Отзывы: