manualshive.com logo in svg

Cairn Dual OptoLED, Инструкция по эксплуатации

Поделиться
Скачать
Cairn Dual OptoLED Скачать руководство пользователя страница 3

Important Safety Information

Please Read Before Installation

For maximum reliability and safety we recommend using the equipment within 
certain guidelines. If in any doubt, then please feel free to contact our 
technical support department (e-mail [email protected]).
The following points should be considered when using the OptoLED for the 
first time:
1.      The OptoLED is capable of producing very intense illumination. The LED 

heads should NEVER be viewed directly. If testing the LEDs then always 
shine them at a white surface and view the resultant reflection or 
fluorescence. This is especially important with ULTRAVIOLET LEDs which 
will not appear bright to the human eye, but can cause permanent 
damage if not used with care.

2.      Our standard LED heads have built in protection to avoid damage, 

however if in any doubt then please check with Cairn as to the rated 
power of the supplied heads, and use accordingly.

3.      The OptoLED is typically supplied in conjunction with our modular 

microscope coupling system. Please refer to the separate 
documentation regarding your particular configuration.

4.      The OptoLED system supports a vast range of different LEDs and LED 

arrays. Different sized LEDs require different condenser lenses. We 
always try to optimise the condensers for the LEDs ordered, but if you 
require help with optimisation then please ask.

Содержание Dual OptoLED




























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды