CAE SimEquip Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 62

CAE SimEquip Скачать руководство пользователя страница 17

©2021 CAE 905K720652 v1.0

17

Setup

6. Connect the EtCO

2

sample line to the T-connector.

7. Connect the mask or the endotracheal tube to the T-connector (at the open end).

Breathing Circuit Assembled with Non-Invasive Mask

To assemble the Transport Ventilator:

1. Unzip the front pocket on the Transport Bag and slide the SimEquip Surface Go 2 tablet

out of the pocket.

Slide Out SimEquip Tablet

2. Plug the power cord into the tablet. Slide the tablet back into the pocket and zip the

pocket closed, leaving the power cord exposed.

3. Place the opposite end of the power cord into the battery pack. Place the battery pack

inside the middle section of the Transport Bag. Zip the middle compartment closed.

4. When facing the front sleeve side of the Transport Bag, open the left compartment on the

bag. Two ports will be visible, labeled:

EXP

and

INSP

.

Limbs

Wye

Elbow

T

EtCO

2

Sample

Line

Mask

«
...
15
16
17
18
19
...
»

Содержание SimEquip































































Отзывы:

Нет отзывов