Cadillac Escalade 2020 Скачать руководство пользователя страница 292 | Manualshive

Страница: 292 / 355

background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

292

VEHICLE CARE

of replacement or alternate tires or
wheels on the vehicle that prevent the
TPMS from functioning properly.
Always check the TPMS malfunction
telltale after replacing one or more
tires or wheels on your vehicle to
ensure that the replacement or
alternate tires and wheels allow the
TPMS to continue to function
properly.

See

Tire Pressure Monitor Operation

for additional information.

Tire Pressure Monitor
Operation

This vehicle may have a Tire Pressure
Monitor System (TPMS). The TPMS is
designed to warn the driver when a
low tire pressure condition exists.
TPMS sensors are mounted onto each
tire and wheel assembly, excluding the
spare tire and wheel assembly. The
TPMS sensors monitor the air
pressure in the tires and transmit the
tire pressure readings to a receiver
located in the vehicle.

When a low tire pressure condition is
detected, the TPMS illuminates the
low tire pressure warning light on the
instrument cluster. If the warning
light comes on, stop as soon as
possible and inflate the tires to the
recommended pressure shown on the
Tire and Loading Information label.
See

Vehicle Load Limits

A message to check the pressure in a
specific tire displays in the Driver
Information Center (DIC). The low tire
pressure warning light and the DIC
warning message come on at each
ignition cycle until the tires are
inflated to the correct inflation
pressure. Using the DIC, tire pressure
levels can be viewed. For additional
information and details about the DIC
operation and displays see

Information Center (DIC)

.

The low tire pressure warning light
may come on in cool weather when
the vehicle is first started, and then
turn off as the vehicle is driven. This
could be an early indicator that the air
pressure is getting low and needs to
be inflated to the proper pressure.

A Tire and Loading Information label,
attached to your vehicle, shows the
size of the original equipment tires
and the correct inflation pressure for
the tires when they are cold. See

Vehicle Load Limits

for an

example of the Tire and Loading
Information label and its location.
Also see

Tire Pressure

The TPMS can warn about a low tire
pressure condition but it does not
replace normal tire maintenance. See

Tire Inspection

Tire Rotation

, and

Caution

Tire sealant materials are not all
the same. A non-approved tire
sealant could damage the TPMS

(Continued)

«
...
290
291
292
293
294
...
»

Содержание Escalade 2020




































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Escalade 2020

UNIVERSAL CJ-2A

Бренд: Jeep Страницы: 27

Бренд: Jeep Страницы: 228

Бренд: Jeep Страницы: 108

Бренд: Jeep Страницы: 525

Бренд: UltraGauge Страницы: 55

Бренд: iArmor Страницы: 6

Бренд: BrandMotion Страницы: 8

Бренд: Buick Страницы: 20

Бренд: Great Wall Страницы: 18

Бренд: WIX Страницы: 2

Бренд: Havis Страницы: 5

1995 C/K Pickup

Бренд: Chevrolet Страницы: 483

Бренд: HOLDEN Страницы: 330

Бренд: Revelation Страницы: 4

Бренд: Ultraplast Страницы: 5

Бренд: Honda Страницы: 279

Бренд: Wallbox Страницы: 13

Бренд: CAME Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды