background image

10

Throttle Control Lever

The throttle control lever is located on the right side of 
the tractor’s dash panel. This lever controls the speed 
of the engine. When set in a given position, the throttle 
will maintain a uniform engine speed. See Figure 4. 

Figure 4

IMPORTANT:

 When operating the tractor with the cutting 

deck engaged, be certain that the throttle lever is 

always

 in the FAST (rabbit) position.

Choke Control

The choke control can be found 
on the left side of the dash panel 
and is activated by pulling the 
knob outward. Activating the 
choke control closes the choke 
plate on the carburetor and aids 
in starting the engine. Refer to 

Starting The Engine

 on page 13 of 

this manual for detailed starting 
instructions.

Brake Pedal

The brake pedal is located on the 
right front side of the tractor 
above the drive pedal along the 
running board. The brake pedal 
can be used for sudden stops or 
setting the parking brake. 

NOTE: 

The brake pedal must

be fully depressed to activate the
safety interlock switch when
starting the tractor

.

Ignition Switch

WARNING: 

Never leave a running

machine unattended. Always disengage PTO,
move shift lever into neutral position, set
parking brake, stop engine and remove key to
prevent unintended starting.

To start the engine, insert the key into the ignition 
switch and turn clockwise to the 

START

 position. 

Release the key into the 

ON

 position once engine has 

fired. See Figure 5. 

Figure 5

Refer to 

Starting The Engine

 on page 13 of this manual for 

detailed starting instructions

The ignition switch is also used to operate the tractor’s 
headlights. Refer to 

Operating The Headlights

 on page 15 

of this manual for detailed instructions.

Drive Pedal

The drive pedal is located below 
the brake pedal on the right front 
side of the tractor along the 
running board. Depress the drive 
pedal with your right foot when 
the tractor shift lever is in either 
FORWARD or REVERSE to 
cause the tractor to move. 
Ground speed is also controlled 
with the drive pedal. The further 
down the pedal is depressed, the faster the tractor will 
travel. The pedal will return to its original position when 
it’s not depressed.

IMPORTANT:

 Always set the parking brake when 

leaving the tractor unattended.

Slow

Fast

Position

Position

 

Off

On/Lights

On

Start

Содержание 1212









































Отзывы: