RCA Headunit signal to
Master Amp only! No RCA
Cables to be attached to
Slave Amplifier.
Amp #1 in Master Mode
Amp #2 in Slave Mode
Fully adjusted Signal
is transferred from
Master to Slave Amp
via RCA Cable.
1-Ohm
Final Impedance
Load!
1-Ohm
Final Impedance
Load!
.
DVC 4-Ohm
Wired in Parallel
to 2-Ohm
Remote turn on
from radio, do not
wire woofers to
this terminal!
1-Ohm Mono Load
Woofer Wiring
DVC 4-Ohm
Wired in Parallel
to 2-Ohm
= 1-Ohm Load.
To amp +
To amp -
DVC 2-Ohm
Wired in Parallel
to 1-Ohm
Or
2-Ohm
Final Woofer Load
2-Ohm
Final Woofer Load
Remote turn on
from radio, do not
wire woofers to
this terminal!
= 1-Ohm Load.
1-Ohm Mono Load
Woofer Wiring
ZRS C5
ZRS C6 / C7
RCA Headunit signal to
Master Amp only! No RCA
Cables to be attached to
Slave Amplifier.
2
-O
h
m
F
in
a
l
Im
p
e
d
a
n
c
e
L
o
a
d
!
Amp #1 in Master Mode
Amp #2 in Slave Mode
Fully adjusted Signal
is transferred from
Master to Slave Amp
via RCA Cable.
USE HEAVY GAUGE
WIRE TO CONNECT
BOTH AMPLIFIERS
SPEAKER “NEGATIVE”
CONNECTIONS.
MINUS TERMINAL OF
WOOFER TO
MASTER AMPLIFIER
POSITIVE TERMINAL.
POSITIVE TERMINAL
OF WOOFER TO
SLAVE AMPLIFIER
POSITIVE TERMINAL.
When bridging two
ZRS C amplifiers, the
final impedance of the
bridged channel shall be
no less than 2 ohms.
Under no circumstances
can you bridge two different
models of amplifiers
4-Ohm
Subwoofer
4-Ohm
Subwoofer
4-Ohm
Subwoofer
4-Ohm
Subwoofer
Four 4-Ohm Subwoofers wired in parallel to the C5, C6 or C7 will equal a 1-Ohm mono load.
ZRS C6 / C7
Daisy Chaining
ZRS Amplifiers
Bridging Two
ZRS Amplifiers
DAISY CHAINING AMPLIFIERS, HOW TO SET SWITCHES,
INPUTS AND REMOTE CONTROL.
When daisy chaining two amplifiers together all pre amp signals including
crossover, phase control, bass equalizer, input gain, subsonic filter, bass
focus are controlled by the Master amplifier. The entire pre amp section of the
Slave amplifier is bypassed. This is done so all you have to do is to set the
Master amplifier and the Slave amplifier will match the Master exactly. There
is no need for any manual matching to occur. This ensures perfect alignment
of your system. One Bass Control knob, plugged in to the Master amplifier
will also control both amplifiers, thereby simplifying your installation as well.
Use the RCA Pre amp Output of the Master Amplifier to feed secondary Full
Range Multi-Channel amplifiers for a Mult-Amp system.
Set Master Amplifier to “MASTER”
Set Salve amplifier to “SLAVE”
Set Phase Shift on both amps to same position.
Set all crossover setting, bass equalizer, subsonic filter, bass focus on
MASTER amp to desired settings.
Use a standard RCA cable to connect MASTER OUT of amplifier #1 (Master)
to SLAVE IN of amplifiers #2 (SLAVE).
Connect woofers as you would typically connect them to each amplifier, not
exceeding a 1 ohm load per amplifier. You can daisy chain as many ZRS C1
as you like while retaining control of your entire system from the Master
amplifier.
When daisy chaining
2 ZRS amplifiers, you
can wire each woofer
to any of the
amplifiers positive or
negative terminals as
they are wired
internally in parallel.
Under no
circumstances can
you daisy chain two
different models of
amplifiers.
BRIDGING AMPLIFIERS
HOW TO SET
SWITCHES, INPUTS
AND REMOTE
CONTROL.
When bridging two amplifiers
together all pre amp signals
including crossover, phase
control, bass equalizer, input
gain, subsonic filter, bass
focus are controlled by the
Master amplifier. The entire
pre amp section of the Slave
amplifier is bypassed. This is
done so all you have to do is to
set the Master amplifier and
the Slave amplifier will match
the Master exactly. There is
no need for any manual
matching to occur. This
ensures perfect alignment of
your system. One Bass
Control knob, plugged in to
the Master amplifier will also
control both amplifiers,
thereby simplifying your
installation as well.
You can use the RCA Pre amp
Output of the Master Amplifier
to feed secondary Full Range
Multi-Channel amplifiers for a
Mult-Amp system.
Set Master Amplifier to
“MASTER”
Set Salve amplifier to SLAVE.
Set Phase Shift on both amps
to same position.
Set all crossover setting, bass
equalizer, subsonic filter,
bass focus on MASTER amp
to desired settings.
Usea standard RCA cable to
connect MASTER OUT of
amplifier #1 (Master) to
SLAVE IN of amplifiers #2
(SLAVE).
C o n n e c t a h e a v y d u t y
speaker wire between the
NEGATIVE terminals of both
amplifiers.
Содержание ZRS C5
Страница 1: ......