background image

Begin with the radio in the off position. Set the fader and all the controls to their center positions. Switch your car ignition or 

accessory  on  and  turn  the  radio  volume  down.  The  illumination  around  the  knobs  should  now  be  lit.  If  nothing  happens  check 

for proper power, ground, and that the fuse is not blown. If all connections have been verified correct, check that the remote wire 

is actually getting power.  

Adjusting the System:

Once you are certain that all the wiring is correct and that the unit turns properly you are ready to adjust the audio section.

 

1. Disconnect the amplifiers remote turn on leads.

 

 

2. Adjust all the amplifier gains to minimum.

 

 

3. Turn the master volume of the CEQ735 to maximum.

 

 

4. Turn the volume of your head unit to maximum and then down a drop.

 

 

5. Switch on any secondary sound source you may have hooked into the MAIN/AUX inputs of the CEQ735. Now 

                     adjust the input level controls found on the top of the unit chassis.

 

 

6. Reduce the master volume of the CEQ735 and reconnect the remote turn on leads to the amplifiers.

 

 

7. Restart the system and increase the volume of the CEQ735 to your desired listening pleasure.

 

 

8. The CEQ735 should be able to run the system even with the amplifier gains set to minimum. If you can not reach your

 

    desired listening level you may raise the amplifier gains. Setting amplifier gains unnecessarily to maximum can cause

 

    cause noise problems in your system.

To the do-it-yourselfer, if you are sure of all your connections and the unit still does not operate properly, we request that you seek 

qualified help to verify that the installation was done properly before exchanging or sending back the unit for repair.

If your system turned on, slowly raise the volume of the CEQ735 the volume should increase from all your speakers. Rotate your

radio balance in conjunction with the CEQ735 fader to make sure that the sound is moving correctly from left to right and front to

rear. It is important that your radio fader and balance be left in their center positions.  

FINAL SYSTEM CHECK

8

Содержание CEQ735













Отзывы: