manualshive.com logo in svg

CADDX Ranger 8000, Руководство по установке

Поделиться
Скачать
CADDX Ranger 8000 Скачать руководство пользователя страница 23

23

THE FOLLOWING LOCATIONS ARE ACCESSIBLE ONLY THROUGH DOWNLOADING

LOCATIONS 186-193: CONTROL PANEL ACCESS CODE

Locations 186-193 contain the eight digit access code the 8000 must receive from the downloading software before
the panel will permit downloading to occur. The factory default code is listed in the instructions provided with the
CADDX download software package. 

LOCATIONS 194-209: CALL BACK TELEPHONE NUMBER

The presence of a phone number in locations 194-209 will cause the control panel to dial back this number after a
successful panel access code has been entered. If a telephone number is present, the control panel will hang up for
approximately 36 seconds (insuring that the calling party has disconnected), then it will call back. Any zero (0) within
the telephone number must be programmed as an "A". If tone dialing is desired, program an "F" in the location where
tone dialing should begin. If the entire number should be tone dialing, program an "F" in location 194. Four second
delays can be obtained anywhere in the sequence by programming a "D" in the appropriate delay location.
WARNING: CALLBACK PHONE NUMBER SHOULD ALWAYS BE REVIEWED FOR ACCURACY BEFORE
DISCONNECTING.

LOCATION 210: ANSWERING MACHINE DEFEAT

Location 210 contains the answering machine defeat enable. To defeat an answering machine, two telephone calls
must be made to the premises. On the first call, let the phone ring the same number of times (or less) as the number
programmed in location 210 (maximum 3). The control panel will detect these rings and start a 45 second timer. If
a call comes in during that 45 second time frame, the control panel will answer on the first ring.  To disable this
feature, program a "0" in this location.

LOCATION 211: LOCAL PROGRAMMING LOCKOUT

Location 211 is used to disable local programming lockout. If a "5" is programmed in this location, all local
programming is locked out. If an "A" is programmed in this location, all programming functions related to the digital
communicator will be locked out. Any other number in location 211 will allow all local programming.

LOCATION 212: CONTROL PANEL SHUTDOWN

Location 212 is used to shut down the control panel. Programming an "A" in this location will completely shutdown
the control panel. The keypad will appear "dead", and the siren and communicator will not operate. WARNING:
EXTREME CARE SHOULD BE TAKEN NOT TO INADVERTENTLY PROGRAM THIS LOCATION.

Содержание Ranger 8000





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды