3
3
4. Fitting and Changing the Gas Cylinder
• Before connecting the appliance to a gas cylinder, ensure that the rubber seal on the regulator is in position and in good condition.
• Carry out this check each time you fit the appliance to a gas cylinder (see fig. 1).
• Blow out any dust from the cylinder opening to prevent possible blockage of the jet.
• Ensure the gas cylinder is fitted or changed in a well ventilated location preferably outdoors, away from any source of ignition such as
naked flames, and away from other people.
• Make sure that the gas cylinder is kept upright at all times. Hand tighten the regulator onto the cylinder until it is fully engaged.
• If there is a leak on your appliance (smell of gas), extinguish all sources of ignition in the vicinity of the appliance. If you wish to check
for leaks on your appliance, use soapy water which is applied to the suspected area. A formation of bubbles will indicate a gas leak.
Check that all the connections are securely fitted and re-check with soapy water. If you cannot rectify the gas leak, do not use the
appliance. Contact your local CADAC stockist for assistance.
• When changing a gas cylinder, first close the cylinder valve and then the appliance valve, making sure the flame is extinguished and
unscrew the regulator. Re-fit the regulator to a full cylinder following the same precautions as described above.
• After the appliance has been fully assembled, perform a gas leak test before operating the appliance.
• Make sure that the gas cylinder is kept upright at all times. Hand tighten the regulator onto the cylinder until it is fully engaged.
5. General Maintenance
• There are no predetermined maintenance intervals for this appliance.
• It is dangerous to use an appliance with a cracked or perished seal and/or hose. Inspect both seals and hose regularly and replace if
they are not in order before using the appliance.
• If the appliance was in use it will be hot. Allow to cool sufficiently before attempting any maintenance.
• CADAC Patio BBQ’s are fitted with spesific CADAC jets to regulate the correct amount of gas. Should the hole in the Jet become
blocked this may result in a small flame or no flame at all. Do not attempt to clean the Jet with a pin or other such device as this may
damage the orifice, which could make the appliance unsafe.
5.1.
Replacing a Blocked Jet
• Ensure that the cylinder valve is closed, then disconnect the appliance from the gas cylinder.
• Remove the grill plates. Remove the flame tamers to expose the burners. Remove the retaining screws of the affected burner.
• Remove the affected burner by lifting it out of its location taking care not to damage the control valve whilst doing so. This will expose
the Jet.
• Unscrew the blocked Jet with a suitable spanner and replace it with a new Jet. Do not use pliers on the Jet as they can cause damage,
making the Jet unusable or impossible to remove.
• Do not over tighten as this may damage the Jet. To re-assemble, reverse the above procedure.
5.2.
Replacement of Hose
• The hose length should not be less than 0.8m or exceed 1.2m. Check the date of manufacture on the hose and replace if it shows
signs of cracking or brittleness. Fitting of a hose is described in Figure 1b. Only an LPG hose that complies with local regulations may
be used with this appliance.
3. Using the appliance
• Place the cylinder inside the cabinet in the space provided.
• Use this appliance only on a firm level surface.
• Before use ensure that the drip cup/tray is in place.
• Make sure the gas cylinder is correctly fitted to the appliance.
• Ensure the cylinder control valve is in the open position.
• To light the appliance using the automatic igniter, push in and turn the control knob in an anti-clockwise direction until spring
resistance is felt. Hold the knob in this position for 3 – 5 seconds to allow the gas to flow and then turn the knob fully anti-clockwise
to the HIGH position. This will cause the automatic lighter to light the burner. Should the burner not ignite the first time, turn the
control knob to the OFF position and wait 5 minutes, repeat the process until the burner ignites.
• Note! All burners are fitted with an automatic igniter.
• Cross lighting: To light the burners using cross lighting, light the left burner as described above.
• To light the remainder of the burners, simply turn their control knobs to the HIGH position while ensuring that the lighting sequence is
such that any burner to be lit up is directly adjacent to a burner which is already burning.
• Manual ignition: To light the burners manually, first remove the cast iron grill plate and the deflector plate directly underneath it.
Ignite a match or firelighter and position it next to the left hand burner. Turn on the gas supply to that burner only by pushing the
control valve in and turning it in an anti-clockwise direction. This will ignite the burner. Once the burner is ignited, carefully replace
the deflector plate and cast iron grill plate. You will now be able to light the remainder of the burners as described in ‘Cross lighting’
above.
• Use the control knobs to adjust the individual burner flame intensity to the desired level by turning the knob anti-clockwise to decrease
the flame and clockwise to increase it (see fig.3).
• After use, first close the valve on the gas cylinder. When the flame is extinguished, close the burner control valves on the appliance by
turning control knobs fully clockwise.
503-0514 LEV7 - (98250)Entertainer 3 & 4 - User Manual (EU & SA).indd 3
2015/12/10 07:25:36 AM
