8
The fan speed is selected by pressing the FAN button. This button
is used to set the fan speed in the following sequence:
Fan Speeds: Low
Medium
High
NOTE:
When the unit is on, the fan will run continuously in
cooling or heating. When in heating, there might be situations
where the fan will slow down or shut off to prevent cold blow.
TURBO MODE
The desired setpoint, either in heating or cooling, can be achieved
faster if TURBO mode is used. After selecting the “HEAT” or
“COOL” mode button, push the “TURBO” button. This will force
the unit to run at super high speed. When the setpoint is satisfied,
push the “TURBO” button again. The unit will run at the selected
fan speed.
When TURBO mode is running, the following is displayed on the
remote control:
OPER
º
F
º
C
HOUR
ON/OFF
:
Turbo
Icon
A09636
Displaying Setpoint or Room Temperatures on Front Panel
The setpoint temperature or room temperature can be displayed on
the front panel. Only setpoint temperature is displayed on the
remote.
º
F
º
C
HOUR
ON/OFF
:
Room
Temperature
Icon
A09638
When the “TEMP” button is pushed once, the temperature
indicator (without thermometer) is displayed. This indicates that
the setpoint temperature is displayed on the front panel.
When the “TEMP” button is pushed a second time, a thermometer
is displayed inside the temperature indicator. This indicates that
the room temperature is displayed on the front panel.
NOTE: If any other button is pushed on remote control, the
temperature will return to the set point temperature. Outdoor
air temperature is not available.
Using Dry Coil Function (X--Fan):
When operating in humid areas, hi--wall units have a DRY COIL
function that will allow the indoor fan to run for a pre--determined
amount of time (10 minutes) after the unit is turned off
(cooling
or dry modes)
to ensure that additional moisture is removed from
coil. Push the “X--FAN” button to enable this feature. This will
be displayed on remote control.
OPER
º
F
º
C
HOUR
ON/OFF
:
Remote
Dry Coil
Icon
A09637
To deactivate this feature, push the “X--FAN” button again.
Selecting the Horizontal Direction Louver Position
When the unit is turned on, the louvers default to the cooling or
heating position.
If the louver position is not providing adequate comfort due to
room layout or where people are gathered, two options are
available to correct the situation:
Setting the louvers in a stationary position
(other than default for heating and cooling):
The stationary position can be one of five (5) default positions.
To change the louver position, press the
“SWING“ button
once. The
icon is displayed on the remote.
OPER
ºF
ºC
HOUR
ON/OFF
:
Swing Icon
A09640
When the
is displayed, the louver will swing continuously
between positions 1 and 5 as shown below.
OFF
0
1
2
3
4
5
6
7
8
A09634
If the “SWING”
button is pushed again,the louver will
move to position 1. If position 2 through 5 is desired, push the
button repeatedly until the desired position (2 through 5)
is displayed on remote control.
Setting the louvers to move continuously:
This setting allows the louvers to move continuously between
either positions 1 through 5, or between positions 6, 7, and 8.
Push the
button once to have louvers swinging between
positions 1 and 5. If position 6, 7, or 8 is desired, push the
button repeatedly until the desired position is displayed on the
remote.
NOTE: Always use the remote control to adjust the horizontal
louver position otherwise, abnormal operation may occur. If
this occurs, turn the unit off and then on again.
Sometimes, in the heating mode, when the
”SWING”
button is pushed, the louvers will not start moving right away.
This is due to the fact that the fan will not start running until
the coil temperature is warm enough to prevent discomfort to
the user by blowing cold air.
