background image

 

Installing the 9A600 Module

2-6

 

The 9A600 module is shipped without ANIMs. To install the ANIMs proceed as 
follows:

1.

Remove the module if it is installed in the SmartSwitch 9500 chassis. To 
remove a module, release (rotate outward) the top and bottom plastic locking 
tabs, then slide the module out of the chassis.

2.

Refer to Figure 2-4. Remove the two screws fastening the coverplate to the 
front standoffs where the ANIM is to be installed. Save the screws.

3.

Lift and remove the coverplate from the top of the front standoffs.

 

Figure 2-4. Removing the Coverplate

 

4.

Refer to Figure 2-5. Hold the ANIM by the provided cutouts on the board of 
the ANIM. 

!

CAUTION

 

The ANIM and 9A600 module are sensitive to static discharges. Use a grounding 
strap and observe all static precautions during this procedure. Failure to do so 
could damage the ANIM and the 9A600 module.

NOTE

 

If you are installing ANIMs in more than one slot, remove the cover plates from all 
the associated slot openings.

A Phillips Head screwdriver is needed to install the ANIMs.

Front
Standoffs

RESER

VED FOR 

ANIM

Coverplate

Содержание SmartSwitch 9500











































Отзывы: