Cabletron Systems 9C114 Скачать руководство пользователя страница 23

Страница: 23 / 26

1-15

Installing the 9Cx14 Chassis

Figure 1-7. Attaching the INB Terminator Modules

Powering up the SmartSwitch 9000

The SmartSwitch 9000 chassis is powered up by following the steps below:

1. Plug one end of the power cord (supplied with the power supply) into the AC

power socket on the lower right front corner of the power supply.

2. Plug the other end of the power cord into an AC receptacle. Turn on the power

supply using the switch located near the power socket.

3. The power supply uses a soft start feature and does a pre-power diagnostic

check. Outputs become enabled within 5 seconds of turning the power on.

4. Check that the PWR and SMB LEDs on the power supply are green.

If the LEDs are any color other than green, refer to the

Power Supply User’s

Guide

100-125v-12A

200-250v-6A

50-60 Hz

POWER SUPPLY MODULE

9C214-1

100%

50%

STATUS

P
W
R

S
N
B

Load

9C614

NON-SECURED

SECURED

NON-SECURED

SECURED

INB
Termination
Connectors

Содержание 9C114



























Результаты поиска

Содержание 9C114

Отзывы:

Похожие инструкции для 9C114

Бренды по названию

Популярные бренды

Cabletron Systems 9C114, Руководство по установке

Результаты поиска

Содержание 9C114

Отзывы:

Похожие инструкции для 9C114

Бренды по названию

Популярные бренды