Cablematic BLE RS-232 Series Скачать руководство пользователя страница 5

Страница: 5 / 9

BLE RS-232 adapter user manual V1.0

2018.05.22

UUID_NOTIFY (~20 bytes)

00031234-0000-1000-8000-00805F9B0130

UUID_RxData (~20 bytes)

00031234-0000-1000-8000-00805F9B0131

UUID_MacID (6 bytes)

00031234-0000-1000-8000-00805F9B0133

UUID_DeviceName (15 bytes)

00031234-0000-1000-8000-00805F9B0134

UUID_Reboot (1 bytes)

00031234-0000-1000-8000-00805F9B0135

UUID_PinID_Setting (6 bytes)

00031234-0000-1000-8000-00805F9B0136

UUID_BLE_CONF (7 bytes)

00031234-0000-1000-8000-00805F9B0132

Byte0

Byte1

Byte2

Byte3

Data bit

Hwfc

Stop Bit

Parity Bit

7,8

0x01:on

0x00:off

2:1

3:1.5

4:2

0x02 : No Parity

0x01 : Odd Parity

0x00 : Even Parity

Byte4

Byte5

Byte6

Baud Rate

Device Mode

Reset To Default

00:9600

01:19200

02:38400

03:57600

04:115200

05:230400

06:2400

07:4800

08:1200

：

460800

：

921600

0x01:on

0x00:off

0x01: Reset

6. Command set via COM port:

Command

Value

Description

Check the connection status between control terminal and the RS-232
adapter. Response: “OK” when the connection is ok. Response:
“ERROR” when the connection is not ok.

Test the RS-232 status when first connect the adapter with the
controller.

(Default)

The command will disable the auto link function.

Inquire the current setting.

BAUD=

This command is used to specify the baud rate of COM port.
The command will need 200 ms delay.

1200

1200 bps

Содержание BLE RS-232 Series










Результаты поиска

Содержание BLE RS-232 Series

Отзывы:

Похожие инструкции для BLE RS-232 Series

Бренды по названию

Популярные бренды

Cablematic BLE RS-232 Series, Руководство пользователя

Результаты поиска

Содержание BLE RS-232 Series

Отзывы:

Похожие инструкции для BLE RS-232 Series

Бренды по названию

Популярные бренды