You can download the complete
manual at the URL
https://clogic-intl.com/clogic-5200
FULL MANUAL DOWNLOAD
Autorange advance multimeter
C-LOGIC 5200
SKU: CLOGIC5200CBINT
INSTRUCTIONS MANUAL
ENGLISH
EN
The meter is a portable, hand-held yet professional meter that features an LCD with
backlight, overload protection and low battery indicator. This meter are easy to use with one
hand, suitable for professional users or amateurs, and ideal for school or home use.
The functions included are the measuring of AC/DC voltage, AC/DC current, resistance,
frequency, duty cycle, capacitance, temperature, continuity and diode test.
SAFETY INFORMATION
Warning
To reduce the risk of electrical shock, product damage or personal injury, please follow
the safety instructions described in the user manual. Read the user manual before using
the meter.
This instrument meets GB/T 13978-92 and GB4793.1-1995 (IEC-61010-1, IEC-61010-2-
032) standards for safety requirements for electronic testing instruments, pollution degree 2
and over voltage rating of CAT lll 1000V and CAT IV 600V.
Follow all safety instructions to ensure safe use of the instrument. Proper use and protection
of the meter will ensure long life of the meter.
PREPARATION
• When using the meter, follow the following safety rules:
1) Always take precaution to prevent electrical shock
2) Never misuse the instrument
• Check to see if the meter or any components were damaged during shipment.
• Check the meter and accessories thoroughly before using.
• Inspect test leads and probes for cracks, breaks or crazes on the insulation before using
the meter.
• Use test leads provided with the unit. lf necessary, replace test leads with identical
specifications.
USE
• Turn the rotary switch to the required function and range to be measured.
• When using the CAT IV environment, if the measuring voltage between terminals and
earth ground exceeds 600V, or in CAT 111 environments voltage measurement between
the terminal and the earth more than 1000V, do not measure voltage.
• Always be careful when working with voltages above 60V DC or 30V AC RMS.
Keep fingers behind the probe barriers while measuring. Never touch probes during
measurement.
• Choose the highest range when the value to be measured is unknown.
• Remove test leads before switching functions on the rotary switch.
• Do not perform resistance, capacitance, diode and continuity measurements on powered
circuits.
• Never connect the test leads across a voltage source while the rotary switch is in the
resistance, diode or continuity mode. Doing so can damage the meter.
• Power off the circuit and discharge capacitors before testing capacitance.
• Do not place the meter in any environment with high pressure, high temperature, dust,
explosive gas o vapor.
• Stop using the meter if any failure or abnormal function is observed.
• Do not use meter unless battery cover is properly installed.
•
Avoid direct sunlight, exposing batteries to humidity, any strong magnetic field, or high
temperatures to ensure the extended life of the meter.
MAINTENANCE
• To avoid electrical shock or personal injury, repairs or servicing not covered in this manual
should be performed only by qualified personnel.
• Remove test leads before opening battery cover.
• To avoid incorrect readings causing electric shock or personal injury, when low battery
symbol “(
)” appears, replace batteries immediately.
• The meter can be cleaned with a soft cloth to remove any oil, grease or grime. Do not use
liquid solvent or detergent.
• When the instrument is not in use, turn rotary switch to “OFF”.
• If the instrument is not to be used for an extended period of time, remove the batteries to
prevent damage to the instrument.
REPLACING THE BATTERIES
Warning
To avoid electrical shock, damage or personal injury, remove test leads before opening
battery cover.
• lf the low battery symbol “
” appears, appears, the battery needs to be changed.
• Unscrew the battery cover from the back of the meter and remove the old battery.
• Insert a new battery and replace the cover and tighten it to the meter.
Note:
Be sure to note the battery polarity when replacing.
REPLACING TEST LEADS
Replace test leads if leads become damaged or worn.
Warning
Use meet EN61010-031 standard, rated CAT.III 1000V, or better test leads.
ACCESSORIES
• Test leads
1 pair
• Short manual
1 pc
• Battery 9V 6F22
1 pc
• Multifunctional test socket
1 pc
• K-type temperature probe
1 pc
MANUFACTURER:
MGL International
APAC:
MGL GLOBAL SOLUTIONS LTD
Flat 4-1, 4/F, No. 35, Section 3 Minquan
East Road. Taipei, Taiwan.
Tel: +886 2-2508-0877
EMEA:
MGL EUMAN S.L.
Parque Empresarial Argame, 33163
Morcín. Asturias, Spain.
Tel: +34 985-08-18-70
AMERICAS:
MGL AMERICA, LLC.
US East Coast:
2810 Coliseum Centre
Drive, Ste. 100. Charlotte, North Carolina,
28217 USA
Tel: +1 833 533-5899
US West Coast:
760 Challenger Street.
Brea, California 92821 USA
Tel: +1 310-728-6220
www.mgl-intl.com
