To select the Chime Volume level, press the ‘VOL’
button on the chime There are 4 selectable volume
levels, the Door Chime is pre-set to the loudest
volume setting.
Volume
Default
Functions:
ON
1: plug Chime into a UK 3pin
socket, 220 – 240V ~ 50Hz.
2: Switch the socket on.
1: plug Chime into a UK 3pin
socket, 220 – 240V ~ 50Hz.
2: Switch the socket on.
3: Chime will ‘Beep’ on Start
4
™
Plug-in & Portable
Wire Free Chime Kit
1:
2:
4:
:3
7:
5:
BY212
1: Push Button
5: Portable Chime
2: Melody Selector
6: Speaker
3: Bell Push Battery
7: Volume control
4: Signal Sent LED
8: Plug-in Chime
ON
6:
6:
8:
7:
1: Place a small flat screwdriver
into the locking clip on the
base of the Bell Push
2: Gently twist
3: The backing plate will unclip
1
3
1: Remove the battery cover of
the Door Chime.
2: Insert 3 X 1.5V Size ‘AA’
batteries (Not Supplied).
3: Make sure the
Positive/Negative terminals
match the internal markings.
4: Chime will ‘Beep’ on Start up.
5: Replace the battery cover
3 x 1.5V ‘AA’
6 Selectable Melodies
1: Tubular 3-Note
4: Solo
2: Big Ben
5: Tubular Score
3: Tubular 2-Note
6: Clarinet
To select a melody for the Door Chime
1: Remove the Back Plate from the Bell
Push
2: Press the Melody Select button.
3:The chime will play the newly selected
sound
4: Press again to select the next melody.
Note: For Front/Back door setup, select a
different melody in one of the Bell Pushes.
CR2032
1: Press and hold the ‘VOL’
buttons on both Door
Chimes, until the Chimes
‘Beep Beep’ (6 Seconds)
2: Press the Bell Push within
60 seconds to learn the
Bell Push to the chimes.
3: The Chimes will ring to
confirm setup, wait 60
seconds for the Chimes
to exit the learn mode
before repressing the Bell
Push.
5
Beep
Beep
Beep
Beep
New Chime
Additional Chime
To add an additional Chime unit to the Door Chime kit
1: Press and hold the ‘VOL’ button on your New Door Chime, until the
Chime goes ‘Beep Beep’ (6 Seconds)
2: Press the Bell Push within 60 seconds to learn the additional
Chime to the Bell Push.
3: Chime will ring to confirm setup, wait 60 seconds for the Chime to
exit the learn mode before repressing the bell push.
Adding Additional Chime/Bell Push:
Beep
Beep
Additional Bell Push
To add an additional Bell Push to the Door
Chime kit
1: Press and hold the ‘VOL’ button on your
Door Chime, until the Chime goes
‘Beep Beep’ (6 Seconds)
2: Press the Bell Push within 60 seconds
to learn the additional Bell Push to the
Chime
3: Chime will ring to confirm setup, wait 60 seconds for the Chime
to exit the learn mode before repressing the bell push.
For Front/back door setup, select a different melody in one of
the Bell Pushes - See Melody Selection.
Note: Maximum of 6 Bell Pushes can be learnt to a single Chime
Front Door
Back Door
1: Insert CR2032 battery
(Supplied) into the battery
holder.
2: Make sure the positive side
is facing upwards.
3: Replace back plate.
2
Warning: Make sure that the batteries are
replaced correctly to avoid battery failure.
Only replace with same or equivalent type.
