BYD ATTO 3 2022 Скачать руководство пользователя страница 188

Страница: 188 / 201

187

WHEN F

AUL

TS OC
CUR

When the Battery Runs

Out

When the vehicle cannot start due to low

battery level, try to start it in the following

steps:
1. Open the hood. (Please refer to

"Maintenance - Self-Maintenance –

Hood".)

2. Connect one end of the red positive (+)

cable to the positive terminal (+) of the

undercharged battery of the vehicle

being rescued.

3. Connect the other end of the red

positive (+) cable to the positive terminal

(+) of the charged battery of the rescue

vehicle.

4. Connect one end of the black negative (-)

cable to the negative terminal (-) of the

charged battery of the rescue vehicle.

5. Connect the other end of the black

negative (-) cable to a suitable grounding

point (a clean and unpainted firm

grounded metal part) of the vehicle

being rescued.

6. Start the rescue vehicle and keep it

running for a while. Then try starting the

vehicle being rescued.

7. After the vehicle being rescued starts

normally, turn off the power of the

rescue vehicle, remove the jumper

cables in the order reverse to that

connecting them and put them away.

8. Close the hood.

WARNING!

•

If the jumper cables are connected

or disconnected in the wrong order,

short circuit may occur, resulting in

vehicle damage or personal injury.

•

When starting the vehicle with jumper

cables, the clamps of the jumper

cables must not contact each other or

any conductive parts other than the

jumper points, to avoid short circuits.

Содержание ATTO 3 2022










































































































































































































Результаты поиска

Содержание ATTO 3 2022

Отзывы:

Похожие инструкции для ATTO 3 2022

Бренды по названию

Популярные бренды

BYD ATTO 3 2022, Руководство пользователя

Результаты поиска

Содержание ATTO 3 2022

Отзывы:

Похожие инструкции для ATTO 3 2022

Бренды по названию

Популярные бренды