AIR-EAGLE
®
XLT
900 MHz RF Transmitter
MODEL 441-HH-4-VBR
FREQUENCY PROGRAMMING
Please read through these instructions completely before beginning
programming procedure!
At any time, you can check the current frequency setting by depressing
Buttons 3 & 4 simultaneously, for approximately 5 seconds, until the TX
LED is illuminated
RED
. Then release all buttons and wait ten seconds for
the LED to turn off. The TX LED will blink
RED
one, two, three or four
times for Frequencies 1 thru 4, or will blink
GREEN
one, two, three or four
times for Frequencies 5 thru 7 accordingly. See table below for
clarification.
LED Flashes:
Indicates Unit is Operating On:
RED
– one time
Frequency 1
RED
– two times
Frequency 2
RED
– three times
Frequency 3
RED
– four times
Frequency 4
GREEN
– one time
Frequency 5
GREEN
– two times
Frequency 6
GREEN
– three times
Frequency 7
To change the setting, follow these steps:
To select from Frequencies 1 thru 4:
1.
Depress Buttons 3 & 4 simultaneously until the TX LED is
illuminated
RED
. (Approximately 5 seconds)
2.
Release Buttons 3 & 4, then while the TX LED is still
illuminated
RED
, depress any of the buttons 1 through 4 to
select frequency 1 through 4. The LED will blink according to
which frequency has been selected. If no button is pressed for
10 seconds, then the transmitter will blink back the current
frequency according to the chart above.
To select from Frequencies 5 thru 7:
1.
Depress Buttons 3 & 4 simultaneously until the TX LED is
illuminated
GREEN
. (Approximately 8 seconds)
2.
Release Buttons 3 & 4, then while the TX LED is still
illuminated
GREEN
, depress any of the buttons 1 through 3 to
select frequency 5 through 7. The LED will blink according to
which frequency has been selected. If no button is pressed for
10 seconds, then the transmitter will blink back the current
frequency according to the chart above.
Programming is now complete, and the transmitter is active for normal
operation.
You may repeat the above procedure if you wish to change the frequency
at any time. See note* in SPECIFICATIONS.
TRANSMITTING MODE SETUP
The transmitter can be set to be in a standard transmission mode or in a
repeater mode where all receivers will repeat the transmission.
To select transmission mode:
1.
Remove one battery from the transmitter
2.
Press and hold button 4 while inserting the battery
3.
Continue holding button 4 for 10 seconds until the LED
starts flashing
GREEN
/
RED
quickly.
4.
Press button 1 for standard mode or button 2 for repeating
mode.
5.
LED will turn
RED
if standard mode selected or
GREEN
if
repeater mode selected.
6.
If no button is pressed for 10 seconds, the LED will
illuminate to show the current transmission mode.
Once the transmission mode has been selected, the LED will continue to
illuminate
RED
(standard mode) or
GREEN
(repeater mode) during all
future transmissions.
NOTES ON TRANSMISSION MODE
The standard transmission mode is best for situations where quick button
response is needed. This type of transmission is typically used when you
’ll
be watching what you
’re controlling, so repeating is not necessary.
For repeating mode there is a short delay added to the button commands
to allow the system to repeat between multiple receivers without collision.
This type of system is usually something where many units spread out
over a large area need to be controlled simultaneously and response
speed isn
’t a priority.
Both types of transmission can be used simultaneously in the same
system although repeating transmissions could cause some lag in the
standard transmissions.
LIMITED WARRANTY STATEMENT
BWI Eagle Inc. warrants the Air-Eagle Remote Control System, if properly used and
installed, will be free from defects in material and workmanship for a period of 1 year
after date of purchase. Said warranty to include the repair or replacement of defective
equipment. This warranty does not cover damage due to external causes, including
accident, problems with electrical power, usage not in accordance with product
instructions, misuse, neglect, alteration, repair, improper installation, or improper
testing. This warranty also does not cover water damage to any handheld transmitter.
This limited warranty, and any implied warranties that may exist under state law,
apply only to the original purchaser of the equipment, and last only for as long as
such purchaser continues to own the equipment. This warranty replaces all other
warranties, express or implied including, but not limited to, the implied warranties or
merchantability and fitness for a particular purpose. BWI Eagle makes no express
warranties beyond those stated here. BWI disclaims without limitation, implied
warranties of merchantability and fitness for a particular purpose. Some jurisdictions
do not allow the exclusion of implied warranties so this limitation may not apply to
you. To obtain warranty service, contact BWI Eagle for a return material
authorization. When returning equipment to BWI Eagle, the customer assumes the
risk of damage or loss during shipping and is responsible for the shipping costs
incurred.
DOCUMENT DATE: 03/08/2021 / PRODUCT REV. 12
105 Bonnie Drive
Butler, PA 16002
(724) 283-4681
Fax (724) 283-5939
