AIR-EAGLE
®
SR
2.4 GHz RF Transmitter
MODEL 38-1500
PROGRAMMING
Please read through these instructions completely before beginning
programming procedure!
At any time, you can check the current frequency setting by depressing
Button 9, for approximately 4 seconds, until the TX LED is illuminated
“
RED
”. Then release all buttons and watch until the TX LED begins to
blink. The TX LED will blink “
RED
” one, two, three or four times for
Frequencies 1 thru 4, or will blink “
GREEN
” one, two, three or four times
for Frequencies 5 thru 8 accordingly. See table below for clarification.
LED Flashes:
Indicates Unit is Operating On:
RED – one time
Frequency 1
RED – two times
Frequency 2
RED – three times
Frequency 3
RED – four times
Frequency 4
GREEN – one time
Frequency 5
GREEN – two times
Frequency 6
GREEN – three times
Frequency 7
GREEN – four times
Frequency 8
To change the setting, follow these steps:
To select from Frequencies 1 thru 8:
1.
Depress Button 9 until the TX LED is illuminated “
RED
”.
(Approximately 4 seconds)
2.
Release Button 9, then while the TX LED is still illuminated
“
RED
”, depress button #1 to select “Frequency 1” or button #2
to select “Frequency 2” etc. If the transmit LED goes out before
you have selected a network, no settings will have changed,
and
the LED will blink corresponding to the frequency that the
TX is currently set to. You must then begin again at step 1 if
you wish to change the current setting.
3.
The TX LED will blink to confirm that your frequency selection
has been accepted, and then will go out. For instance, if you
have selected Frequency #1, the TX LED will blink “
RED
”
once
to confirm. If you have selected Frequency #6, the TX LED
blinks “
GREEN
” two
times
to confirm.
Programming is now complete and the transmitter is active for normal
operation.
You may repeat the above procedure if you wish to change the frequency
at any time. See note* in SPECIFICATIONS.
SPECIFICATIONS
Keypad
Durable Sealed Membrane Keypad –
Eliminates Dust, Dirt and Moisture
Failures
Enclosure
ABS Plastic – with IP66 Rating
Power Requirements
3.0 VDC
Battery Type
(2) 1.5V lithium each, size AAA , to
equal 3.0VDC nominal.
*Note: Current frequency settings are maintained in flash
memory during battery replacement. No reprogramming of
frequency settings is necessary!
Battery Life
(Active Usage)
Up to 6 months
Battery Life
(Sleep Mode)
Up to 1 Year
Transmit Frequency
2.4GHz Spread Spectrum
RF Output Power
1 mW
Transmit Channels
Eight Independent Network
Frequencies
Transmit Range
Approximately 300 Feet
Operating Temperature
-40
o
F to +185
o
F
LIMITED WARRANTY STATEMENT
BWI Eagle Inc. warrants the Air-Eagle Remote Control System, if properly
used and installed, will be free from defects in material and workmanship
for a period of 1 year after date of purchase. Said warranty to include the
repair or replacement of defective equipment. This warranty does not
cover damage due to external causes, including accident, problems with
electrical power, usage not in accordance with product instructions,
misuse, neglect, alteration, repair, improper installation, or improper
testing. This limited warranty, and any implied warranties that may exist
under state law, apply only to the original purchaser of the equipment, and
last only for as long as such purchaser continues to own the equipment.
This warranty replaces all other warranties, express or implied including,
but not limited to, the implied warranties or merchantability and fitness for
a particular purpose. BWI Eagle makes no express warranties beyond
those stated here. BWI disclaims without limitation, implied warranties of
merchantability and fitness for a particular purpose. Some jurisdictions do
not allow the exclusion of implied warranties so this limitation may not
apply to you. To obtain warranty service, contact BWI Eagle for a return
material authorization. When returning equipment to BWI Eagle, the
customer assumes the risk of damage or loss during shipping and is
responsible for the shipping costs incurred.
DOCUMENT DATE: 21-Feb-12 / REV. 3
105 Bonnie Drive
Butler, PA 16002
(724) 283-4681
Fax (724) 283-5939
www.bwieagle.com
