background image

8

CAUTION

CAUTION

CAUTION

FIRE PREVENTION

 DO NOT operate the log splitter near an open flame or spark. Hydraulic oil and 

fuel are flammable and can explode.

 DO NOT fill the fuel tank while the engine is hot or running. Allow the engine to 

cool before refueling�

 DO NOT smoke while operating or refueling the log splitter� Petrol fumes can 

easily explode�

 Refuel the log splitter in a clear area with no fuel fumes or spilled fuel� Use an 

approved fuel container� Replace the fuel cap securely� If fuel has spilled, move 

the log splitter away from the area of the spill and avoid creating any source of 

ignition until the spilled fuel has evaporated�

 Keep a Class B fire extinguisher on hand when operating this log splitter in dry 

areas as a precautionary measure against possible flying sparks.

 Drain the fuel tank prior to storage to avoid the potential fire hazard. Store fuel in 

an approved, tightly sealed container� Store the container in a cool, dry place�

 Turn the fuel shut off valve on the engine to the “OFF” position before towing the 

log splitter. Failure to do so may result in flooding the engine.

TOWING SAFETY

 Check all local and state regulations regarding towing, licensing, and lights before 

towing your log splitter�

 Check before towing to make sure that the log splitter is correctly and securely 

attached to the towing vehicle and that the safety chains are secured to the hitch 

or bumper of the vehicle with enough slack to allow turning� Always use a Class I, 

2” ball with this log splitter�

 DO NOT carry any cargo or wood on the log splitter�

 DO NOT allow anyone to sit or ride on the log splitter�

 Disconnect the log splitter from the towing vehicle before operating it�

 Use care when backing up with the log splitter in tow to avoid jack-knifing. Allow for 

added length of the log splitter when turning, parking, crossing intersections and in 

all driving situations�

 DO NOT exceed 70km/h when towing your log splitter. Towing the log splitter 

at speeds higher than 70km/h could result in loss of control, damage to the 

equipment, serious injury or death� Adjust towing speed for terrain and conditions� 

Be extra cautious when towing over rough terrain especially railroad crossings�

IMPORTANT NOTE

This log splitter is equipped with an internal combustion engine and should not be 

used on or near any unimproved forest-covered, brush covered or grass-covered 

land unless the engine’s exhaust system is equipped with a spark arrester meeting 

applicable local or state laws (if any). If a spark arrester is used, it should be 

maintained in effective working order by the operator�

Never operate the log splitter indoors or in a contained are as there is a danger 

from exhaust fume.

Safety Information

Содержание BWMLS30H





























Отзывы: