BVM Grumman F-9F Cougar Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 42

BVM Grumman F-9F Cougar Скачать руководство пользователя страница 34

BVM ®2015 34 Printed 7/3/2019

Sequencer Instructions Continued

Red Button: (never used)

Red button:

Manual gear up/down button when radio is off but system powered (no

signal detected), and inoperative when radio is on or low pressure safe mode is activated. A
battery could be connected, during aircraft setup, to the Gear input to power the system
without a radio system connected. This button will not be used by most users.

LEDs: (Visible with power on)

Blue LED:

The blue LED displays the commanded landing gear position from the

receiver. When the blue LED is “on”, the gear is down; while the blue LED is off the gear is
up. The blue LED will flash when no signal or incorrect gear switch position is received from
the radio when the system is turned on.

Notice: When the landing gear is down, the blue LED must be on; this is the default gear
down signal for system. Otherwise the landing gear will be commanded “up” when low
pressure safe mode is activated. Verify your landing gear is extended when pressure is below
the failsafe value.

Red LED:

The red LED indicates for pressure warning, LED will flash when low

pressure safe mode is activated. Re-pressurize the air system above the safe pressure to
resume operation.

Green LED:

The green LED indicates receiver voltage is displayed on LCD screen.

Light System

NOTE: Your Aircraft comes with the light system
pre-installed with only one connection to the
receiver required. If you decide to relocate or
modify the system, see below.



Use sticky back Velcro to secure the Light

Controller to the side of the fuselage.

Note: The light controller has a plug
labeled “LED” that plugs into the light
channel on the RX. A second wire labeled
“GEAR” connects to the landing gear
sequencer. This allows the landing lights to turn off when the gear is up.

Note: “Thro” input is not used. There should be one set of open pins on the output
side of the light controller, these are unused.

The light channel coming from the RX has three positions, Off, NAV Only, and NAV
and Landing lights.

«
...
32
33
34
35
36
...
»

Содержание Grumman F-9F Cougar











































Отзывы:

Нет отзывов