Butts of Bawtry TBT2586 Скачать руководство пользователя | Manualshive

Страница: 18 / 39

background image

pull the starter handle again to start the engine.

10. Pull up the front handle guard toward the front

handle to release brake. Then, allow the engine to

warm up with the trigger pulled slightly.

(1) Throttle trigger

(2) Rear handle

(3) Throttle trigger lock lever

Before you start the engine, make sure the saw

chain is not contacting anything. Make sure the

chain brake always is activated before each

starting.

■

CHECKING OIL SUPPLY

After starting the engine, run the chain at medium

speed and see if chain oil is scattered off as

shown in the figure.

Chain oil

The chain oil flow can be changed by inserting a

screwdriver in the hole on bottom of the clutch

side. Turn the shaft counter-clockwise to increase

the oil flow. Turn the shaft clockwise to decrease

the oil flow. Adjust according to your work

conditions.

(1) Chain oil flow adjusting shaft

The oil tank should become nearly empty by the

time fuel is used up. Be sure to refill the oil tank

every time when refueling the saw.

«
...
16
17
18
19
20
...
»

Содержание TBT2586








































Отзывы:

Нет отзывов

Похожие инструкции для TBT2586

Бренд: Royal Страницы: 144

Бренд: ICFR Страницы: 64

Бренд: Stiga Страницы: 360

Бренд: Poulan Pro Страницы: 16

Бренд: Poulan Pro Страницы: 38

Бренд: Poulan Pro Страницы: 18

Бренд: Poulan Pro Страницы: 19

Бренд: Poulan Pro Страницы: 19

Бренд: YATO Страницы: 120

Бренд: Gama Garden Страницы: 17

Бренд: Gardif Страницы: 27

Бренд: Oleo-Mac Страницы: 216

Бренд: Feider Страницы: 23

Бренд: Makita Страницы: 212

Бренд: Makita Страницы: 136

Бренд: Garland Страницы: 172

Бренд: Black & Decker Страницы: 124

Бренд: Echo Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды