TABLE TOP ASSEMBLY
STEP 5
Required Items:
Table Arms (#6)
X4
Adjustable Knobs (#7)
X4
1 1/4” Bolts (#8)
X8
1/4” Nuts (#9)
X8
Table Tops (#10)
X4
Required Items:
Table Tops (#10)
X4
Table Top Mounting Brackets (#11)
X4
M6x16 Mounting Bracket Screws (#12)
X32
STEP 3
BASE PLATE ASSEMBLY
STEP 2
BASE ASSEMBLY
Required Items:
Leg Attachment Plate (#3)
1/2” Screw (#4)
X12
Required Items:
Pneumatic Pistons (#5)
X4
6
7
Diagram B (Side View)
Outer
Inner
10
6
8
10
10
11
12
9
FINAL ADJUSTMENTS
STEP 6
Use Adjustment Knobs (#7) to secure the table tops at the desired height.
Tip the entire assembly over (legs in air). Secure Bases
together by bolting the Attachment Plate to the underside
of Base A (16 screws). Tighten screws securely.
Insert 1 1/4” Bolts (#8) into Table Arm (#6) and tighten with 1/4“ Nut (#9).
Start with inner pre-drilled hole - this is to stop the Table Tops from hitting
the arm. Repeat on all four Table Arms.
Slide Table Tops (#10) onto Table Arms -
See Diagram B
. Use Adjustable
Knobs (#7) to secure tops.
Insert 1 1/4” Bolts (#8) into outer pre-drilled hole of Table Arm (#6). Tighten
with 1/4” Nut (#9) - this is to stop the Table Tops from sliding off the arm.
Insert Table Arms (#6) into the assembled base. Ensure the “L” shaped
bracket is held to one side while inserting the arm tops into the center
post.
Tip the frame, placing it on its legs. Place Pneumatic Pistons
(#5) into frame tubes. These pistons are helpful when
adjusting the height of each table top.
Operation:
Two offset casters have been provided to ensure easy & safe relocation of the table. To move the table, lift the table from
opposite side of the casters by 10” off the floor. Adjust glides to level & stabilize the table. Secure by tighten the locking nut.
TABLE TOP / MOUNTING BRACKET ASSEMBLY
STEP 4
Lay Table Top (#10) on a level floor with
pre-drilled holes pointing up. Using the
Allen Wrench provided, secure Table Top
Mounting Bracket (#11) using the M6x16
Mounting Bracket Screws (#12). Repeat
on all Table Tops (#10).
OVERALL:
48” X 48” (EXTENDED - 58” X 58”)
INDIVIDUAL TOP:
26”W X 22”D
HEIGHT ADJUSTMENT:
26” - 36”
20” - 30” -
OPTIONAL
BFL-4(4/1) SPECIFICATIONS
ADDITIONAL MODELS:
BFL-2(1/1)
BFL-4(2/2)
4
3
Top View
5
Pneumatic Pistons:
Place the
end with the spring into the PVC
tube before inserting into frame.
Required Items:
Base A (#1)
Base B (#2)
1/2” Screw (#4)
X4
Place Base A (#1) onto a flat
surface. Position Base B (#2) at 90
degrees to Base A (#1). Push Base
B (#2) down onto Base A (#1) until
the tops of the center post are
flush.
Use 1/2 Screws (#4) to secure
bases (Do not over tighten).
1
2
4
!
IN ORDER FOR THE BFL-4(4/1) TO BE MOVED
PROPERLY AND SAFELY, PLEASE MAKE SURE
BOTH TRANSPORT CASTERS (#13) ARE
POINTING IN THE SAME DIRECTION BEFORE
PROCEEDING. IF NECESSARY, PLEASE SEE
STEP 1.
13
