background image

 

28 

REQUIRED WARRANTY CLAIM PROCEDURE 

1.  In order to validate this Limited Warranty, the Warranty Registration card must be postmarked to 

Bushtec Manufacturing & Sales, Inc., no later than thirty (30) days following the purchase of your 
Bushtec Performance Sport Trailer.  IF THIS SIGNED WARRANTY REGISTRATION CARD 
IS NOT SIGNED AND POSTMARKED BY THE THIRTIETH DAY AFTER PURCHASE OF 
THE TRAILER, ALL EXPRESS WARRANTIES SHALL BE NULL AND VOID. 

2.  Within five (5) days after discovering a problem with your Bushtec Performance Sport Trailer; 

a. 

If purchased from a Bushtec Manufacturing & Sales, Inc. Dealer, return you trailer for 
inspection to your Bushtec Manufacturing & Sales, Inc. Dealer where you bought your 
trailer.  Dealers are responsible for fixing minor problems without charge to you or the 
factory. 

b.  If purchased from Bushtec Manufacturing & Sales, Inc., contact Bushtec Manufacturing 

& Sales, Inc., by phone, fax, or e-mail to report the issue. 

3.  All warranty claims must be registered in writing by registered letter or fax with Bushtec 
Manufacturing & Sales, Inc., during the applicable warranty periods.   No claims considered 
without prior notice, or beyond the applicable warranty period. 

 

4.  Bushtec Manufacturing & Sales, Inc., will acknowledge such receipt of a claim to the claimant. 
5.  Any defective part(s) must be sent by prepaid freight to Bushtec Manufacturin g & Sales, Inc., 
in order to qualify the claimant for replacement under this Limited Warranty.   You must, at your 
expense, deliver, mail, or ship the product, together with a copy of the original Bill of Sale, and 
this Limited Warranty Statement, as proof of warranty coverage, to the company’s location.. ANY 
DEFECTIVE PARTS MUST BE REUTRNED TO BUSHTEC MANUFACTURING & SALES, 
INC., WITHIN 30 DAYS FROM DATE OF APPROVAL TO QUALIFY FOR 
REPLACEMENT. 
6.  Bushtec Manufacturing & Sales, Inc., will not reimburse any claimant for any adjustment or 
repair of a Bushtec Manufacturing & Sales, Inc., trailer without prior written approval by Bushtec 
Manufacturing & Sales, Inc. 
7.  If you return your trailer for repair to the factory, we will warrant the repair or replacement 
parts for a year from the date of repair.  If authorized repair is made outside of the factory, Bushtec 
Manufacturing & Sales, Inc., will not warrant such repair work or replacement parts. 
8.  Bushtec Manufacturing & Sales, Inc., reserves the right to not pay unreasonable costs for 
replacement or repair of defects in Bushtec Manufacturing & Sales, Inc., trailers and may, at its 
discretion, establish a reasonable reimbursement for any authorized work performed under the 
terms of this Limited Warranty. 
 

THE END USER OF THIS PRODUCT ASSUMES ALL LIABILITY AND RESPONSIBILITIES THAT 
MAY ARISE DUE TO BUT NOT LIMITED TO, NEGLIGENCE FROM IMPROPER INSTALLATION 
OR USE OF BUSHTEC PRODUCTS.  THIS INCLUDES OVERLOADING, EXCEEDING THE 
RECOMMENDED LOAD LIMITS AND IMPROPER MAINTENANCE.  BUSHTEC 
MANUFACTURING & SALES, INC., MAKES NO OTHER EXPRESS OR IMPLIED WARRANTIES 
AND THERE ARE NO OTHER WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON 
THE FACE OF THIS LIMITED WARRANTY.  END OF WARRANTY. 

Содержание Quantum GL





























Отзывы: