11
Unfolding and Adjusting Lower Handle
WARNING
• Folding or unfolding the handle improperly can damage the cables, causing an
unsafe operating condition.
• Do not damage the cables when folding or unfolding the handle.
• If a cable is damaged, contact an authorized Bushranger
®
Service Dealer.
Install Cup Holder (Fig. 1)
• Open attachment bag find 4 PCS M4x15 screw and find the cup holder (P) in packing box.
• Install cup holder (P) to upper handle assembly and lock screw.
Unfolding and Adjusting Handle Assembly
To raise handle assembly:
• Pull up and back on the lower handle (1) until it is aligned with the hole position of
the arm support and the mower housing.
• To secure the lower handle (1) in place, lock the lower screw (3).
• Open the upper cam locks (2).
• Pull up and back on the upper handle to raise it into operating position.
• To secure the upper handle in place, close the upper cam locks (2).
NOTE:
If the upper handle is loose or separated from the lower handle, tighten the
knobs on the upper handle locks by turning them clockwise.
Installing The Grass Catcher
• Make sure all rotating parts have come to a stop.
• Lift the rear discharge door (1).
• Lift the grass catcher by its handle (2) and place under the rear discharge
door so that the hooks (3) on the grass catcher are seated on the door rod (4).
• Release the rear discharge door. When installed correctly, the hooks on the grass
catcher will extend through the openings on the rear discharge door.
NOTE:
When using the grass catcher, do not install either the side discharge deflector
or the mulching plug.
Installing/Removing The Mulching Plug
• Make sure all rotating parts have come to a stop.
• To remove the mulching plug, lift the rear discharge door (1).
• Grasp the handle (2) of the mulching plug.
• Lift and pull the mulching plug out using the handle.
1
3
2
2
4
3
1
14
UNFOLDING AND ADJUSTING LOWER HANDLE
WARNING
Folding or unfolding the handle improperly can damage the cables, causing an
unsafe operating condition.
•
Do not damage the cables when folding or unfolding the handle.
•
If a cable is damaged, contact an Authorized Service Dealer.
UNFOLDING AND ADJUSTING HANDLE ASSEMBLY
a. To raise handle assembly:
•
Pull up and back on the lower handle (1) until it is
aligned with the hole position of the arm support
and the mower housing.
•
To secure the lower handle (1) in place, lock the
lower screw (3).
•
Open the upper cam locks (2).
•
Pull up and back on the upper handle to raise it
into operating position.
•
To secure the upper handle in place, close the
upper cam locks (2).
NOTE: If the upper handle is loose or separated from
the lower handle, tighten the knobs on the upper
handle locks by turning them clockwise.
INSTALLING THE GRASS CATCHER BAG
•
Lift the rear disc harge door (1).
•
Lift the grass catc her by its handle (2) and
place under the rear disc harge door so
that the hooks (3) on the grass catc her are
seated on the door rod (4).
•
Release the rear disc harge door. When
installed correctly, the hooks on the grass
catcher will extend through the openings on
the rear disc harge door.
NOTE: When using the grass catcher, do not
install either the side discharge de
fl
ector or the
mulching plug.
1
3
2
2
4
3
1
14
UNFOLDING AND ADJUSTING LOWER HANDLE
WARNING
Folding or unfolding the handle improperly can damage the cables, causing an
unsafe operating condition.
•
Do not damage the cables when folding or unfolding the handle.
•
If a cable is damaged, contact an Authorized Service Dealer.
UNFOLDING AND ADJUSTING HANDLE ASSEMBLY
a. To raise handle assembly:
•
Pull up and back on the lower handle (1) until it is
aligned with the hole position of the arm support
and the mower housing.
•
To secure the lower handle (1) in place, lock the
lower screw (3).
•
Open the upper cam locks (2).
•
Pull up and back on the upper handle to raise it
into operating position.
•
To secure the upper handle in place, close the
upper cam locks (2).
NOTE: If the upper handle is loose or separated from
the lower handle, tighten the knobs on the upper
handle locks by turning them clockwise.
INSTALLING THE GRASS CATCHER BAG
•
Lift the rear disc harge door (1).
•
Lift the grass catc her by its handle (2) and
place under the rear disc harge door so
that the hooks (3) on the grass catc her are
seated on the door rod (4).
•
Release the rear disc harge door. When
installed correctly, the hooks on the grass
catcher will extend through the openings on
the rear disc harge door.
NOTE: When using the grass catcher, do not
install either the side discharge de
fl
ector or the
mulching plug.
1
2
3
15
EN
INSTALLING/REMOVING THE MULCHING PLUG
•
To remove the mulching plug, lift the rear
discharge door (1).
•
Grasp the handle (2) of the mulching plug.
Lift and pull the mulching plug out using the
handle.
•
The mulching plug (3) is in serted at an angle,
so it requ ires some force to remove it.
•
The mulching plug must be removed in order
to inst all the grass catc her bag.
•
The mulching plug must be re-inst alled when
the grass catc her bag is removed.
NOTE: When mulching, do not install either the
side discharge de
fl
ector or the grass catcher bag.
INSTALLING SIDE DISCHARGE CHUTE
•
Lift the side discharge cover (1).
•
Align the grooves (2) on the discharge
chute (3) with the pins (4) on the underside
of the discharge cover (1).
•
Lower the discharge chute until the hooks
on the mower deck are secured in the
openings in the discharge chute.
•
Release the side discharge cover.
NOTE: When using side discharge, do not
install the the grass catcher bag. Ensure the
mulch plug is installed.
2
3
4
1
ASSEMBLY
INSTALL CUP HO
LDER
(1)
1
1.
Install cup holder
:
• Open attachment bag
fi
nd 4 PCS M4x15 screw
and
fi
nd the cup holder (P) in packing box.
• Install cup hodler (P) to upper handle assembly
and lock screw.
1a
F
M
H
13
• Do not insert battery until assembly is complete and you are ready to mow.
Failure to comply could result in accidental starting and possible serious personal
injury.
• To prevent accidental starting that could cause serious personal injury, always
remove the battery from the product when assembling parts.
• Never operate the mower without the proper safety devices in place and
working. Never operate the mower with damaged safety devices. Operation
of this product with damaged or missing parts could result in serious personal
injury.
UNFOLDING AND ADJUSTING HANDLE ASSEMBLY (2)
a. To raise handle assembly:
• Pull up and back on the lower handle (F) until
it is aligned with the hole position of the arm
support and the mower housing.
• To secure the lower handle (F) in place, lock
the lower screw (M).
• Open the upper cam locks (H).
• Pull up and back on the upper handle to raise
it into operating position.
• To secure the upper handle in place, close the
upper cam locks (H).
NOTE: If the upper handle is loose or separated
from the lower handle, tighten the knobs on the
upper handle locks by turning them clockwise.
2a
P
3
2
1
3
4
2
1
3
2
1
