Bush Hog HT417 Скачать руководство пользователя | Manualshive

Страница: 68 / 82

background image

OPERATION

HT417/HT417H 05/22

Operation Section 4-22

© 2022 Alamo Group Inc.

OPERA

TION

13. TRANSPORTING THE TRACTOR AND IMPLEMENT

Inherent hazards of operating the tractor and implement and the possibility of accidents are not left behind
when you finish working in an area.  Therefore, the operator must employ good judgement and safe operation
practices  when  transporting  the  tractor  and  implement  between  locations.    By  using  good  judgement  and
following  safe  transport  procedures,  the  possibility  of  accidents  while  moving  between  locations  can  be
substantially minimized.

OPS-U- 0017

Never allow children or other persons to ride on the Tractor or Implement.
Falling off can result in serious injury or death.

(SG-10)

13.1 Transport Instructions for Manual Fold

Before transporting the implement, it is necessary raise lateral arms 1 & 2. To do this, first check that spring pin
4, is not touching tab C (RH and LH side). Then raise lateral arms 1 & 2 by pulling on guards A-B until pin 4 of
the spring strut assembly enters hole D (RH and LH side) of the inside pipe of the strut assembly.

OPS-HT- 0055_A

«
...
66
67
68
69
70
...
»

Содержание HT417



















































































Отзывы:

Нет отзывов

Похожие инструкции для HT417

Бренд: Little Giant Ladder Страницы: 3

Бренд: WERNERCO Страницы: 64

Бренд: U-Line Страницы: 6

Бренд: KTL Страницы: 3

Бренд: abc Страницы: 4

Бренд: Main Access Страницы: 7

BuildMan I-BM6S

Бренд: MetalTech Страницы: 12

Бренд: Vestil Страницы: 11

Roof Zone 48589

Бренд: TIE DOWN Страницы: 2

Бренд: CRL Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды