background image

CONGRATULATIONS!

You have invested in the best implement of its type on the market today.

The  care  you  give  your  Bush  Hog  implement  will  greatly  determine  your  satisfaction  with  its
performance and its service life. We urge a careful study of this manual to provide you with a
thorough  understanding  of  your  new  implement  before  operating,  as  well  as  suggestions  for
operation and maintenance.

If your manual should become lost or destroyed, Bush Hog will be glad to provide you with a
new copy. Order from Bush Hog, 2501 Griffin Ave., Selma, Alabama 36703. Most of our man-
uals can also be downloaded from our website at www.bushhog.com.

As an authorized Bush Hog dealer, we stock genuine Bush Hog parts which are manufactured
with the same precision and skill as our original equipment. Our trained service personnel are
well informed on methods required to service Bush Hog equipment,
and are ready and able to help you.

Should you require additional information or assistance, please contact us.

YOUR AUTHORIZED

BUSH HOG DEALER

BECAUSE BUSH HOG MAINTAINS AN ONGOING
PROGRAM OF PRODUCT IMPROVEMENT, WE 
RESERVE THE RIGHT TO MAKE IMPROVEMENTS IN 
DESIGN OR CHANGES IN SPECIFICATIONS WITH-
OUT INCURRING ANY OBLIGATION TO INSTALL 
THEM ON UNITS PREVIOUSLY SOLD.

BECAUSE OF THE POSSIBILITY THAT SOME
PHOTOGRAPHS IN THIS MANUAL WERE TAKEN OF 
PROTOTYPE MODELS, PRODUCTION MODELS MAY 
VARY IN SOME DETAIL. IN ADDITION, SOME
PHOTOGRAPHS MAY SHOW SHIELDS REMOVED 
FOR PURPOSES OF CLARITY. NEVER OPERATE
THIS IMPLEMENT WITHOUT ALL SHIELDS IN PLACE.

Содержание AIR TUNNEL FINISHING MOWER ATH 900





















Отзывы: