BUSCH R 5 RA 1000 B Скачать руководство пользователя страница 32

Страница: 32 / 40

11 | Troubleshooting

32 / 40

0870201062_RA1000-1600B_Ex_-0007_IM_en

11 Troubleshooting

DANGER

Live wires.

Risk of electrical shock.

• Electrical installation work must only be executed by qualified personnel.

CAUTION

Hot surface.

Risk of burns!

• Prior to any action requiring touching the machine, let the machine cool down first.

Illustration showing parts that may be involved during troubleshooting:

CPL

Problem

Possible Cause

Remedy

The machine does not start. The motor is not supplied

with the correct voltage.

• Check the power supply.

The motor is defective.

• Replace the motor.

The coupling (CPL) is de-
fective.

• Replace the coupling

(CPL).

The machine does not reach
the usual pressure on the
suction connection.

Oil level too low.

• Top up oil.

The inlet screen (IS) is par-
tially clogged.

• Clean the inlet screen (IS).

The inlet filter cartridge (op-
tional) is partially clogged.

• Replace the inlet filter

cartridge.

Internal parts are worn or
damaged.

• Repair the machine (con-

tact Busch).

The machine runs very nois-
ily.

Worn coupling (CPL).

• Replace the coupling

(CPL).

Stuck vanes.

• Repair the machine (con-

tact Busch).

Defective bearings.

• Repair the machine (con-

tact Busch).

Содержание R 5 RA 1000 B









































Результаты поиска

Содержание R 5 RA 1000 B

Отзывы:

Похожие инструкции для R 5 RA 1000 B

Бренды по названию

Популярные бренды

BUSCH R 5 RA 1000 B, Инструкция по эксплуатации

Результаты поиска

Содержание R 5 RA 1000 B

Отзывы:

Похожие инструкции для R 5 RA 1000 B

Бренды по названию

Популярные бренды