manualshive.com logo in svg

BUSCH PANDA WZ 0250 B, Инструкция по эксплуатации

Поделиться
Скачать
BUSCH PANDA WZ 0250 B Скачать руководство пользователя страница 7

Transport | 3

Instruction Manual PANDA WZ 0250-0500 B_EN_en

7 | 36

3

Transport

WARNING

Suspended load.
Risk of severe injury!

●

Do not walk, stand or work under suspended loads.

WARNING

Lifting the machine using the motor eye bolt.
Risk of severe injury!

●

Do not lift the machine using the eye bolt fitted to the motor. Only lift the machine as shown.

NOTICE

In case the machine is already filled with oil.
Tilting a machine that is already filled with oil can cause large quantities of oil to ingress into
the cylinder.

●

Drain the oil prior to every transport or always horizontally transport the machine.

●

To find out the weight of the machine, refer to the chapter 

Technical Data

 [

➔

 30] or the

nameplate (NP).

●

Use appropriate slings.

●

Check the machine for transport damage.

If the machine is secured to a base plate:

●

Remove the machine from the base plate.

Содержание PANDA WZ 0250 B





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды