background image

Overhaul | 8

0870569132_SV_SD_DC1010-1040C_-0005_IM_en

17 / 24

8

Overhaul

WARNING

Machines contaminated with hazardous material.

Risk of poisoning!

Risk of infection!

If the machine is contaminated with hazardous material:

• Wear appropriate personal protective equipment.

NOTICE

Improper assembly.

Risk of premature failure!

Loss of efficiency!

• It is highly recommended that any dismantling of the machine that goes beyond any-

thing that is described in this manual should be done through Busch.

In case of the machine having conveyed gas that was contaminated with foreign materi-
als which are dangerous to health:

• Decontaminate the machine as much as possible and state the contamination

status in a ‘Declaration of Contamination’.

Busch will only accept machines that come with a completely filled in and legally binding
signed ‘Declaration of Contamination’ (form downloadable from

www.buschvacuum.com

).

9

Decommissioning

• Shut down the machine and lock against inadvertent start up.

• Vent the connected lines to atmospheric pressure.

• Disconnect all connections.

If the machine is going to be stored:

• See 

Storage [

 7]

.

9.1 Dismantling and Disposal

• Separate special waste from the machine.

• Dispose of special waste in compliance with applicable regulations.

• Dispose of the machine as scrap metal.

Содержание DC 0025 C

























Отзывы: