BUSCH COBRA NC 0600 C Скачать руководство пользователя страница 9

Страница: 9 / 40

Storage | 4

0870567092_NC0630C_WCV_A0006_IM_en

9 / 40

Machine weight:

see the technical data or the nameplate (NP)

WARNING

Lifting the machine using the motor eye bolt.

Risk of severe injury!

• Do not lift the machine using the eye bolt fitted to the motor. Only lift the machine as

previously shown.

• Check the machine for transport damage.

If the machine is secured to a base plate:

• Remove the machine from the base plate.

Storage

• Seal all apertures with adhesive tape or reuse provided caps.

If the machine is to be stored for more than 3 months:

• Wrap the machine in a corrosion inhibiting film.

• Store the machine indoors, dry, dust free and if possible in original packaging

preferably at temperatures between 5 ... 55 °C.

Installation

5.1 Installation Conditions

NOTICE

Use of the machine outside of the permitted installation conditions.

Risk of premature failure!

Loss of efficiency!

• Take care that the installation conditions are fully complied with.

• Make sure that the environment of the machine is not potentially explosive.

• Make sure that the ambient conditions comply with the

Technical Data [

►

36]

• Make sure that the environmental conditions comply with the protection class of the

motor and the electrical instruments.

• Make sure that the installation space or location is vented such that sufficient cooling

of the machine is provided.

Содержание COBRA NC 0600 C









































Результаты поиска

Содержание COBRA NC 0600 C

Отзывы:

Похожие инструкции для COBRA NC 0600 C

Бренды по названию

Популярные бренды

BUSCH COBRA NC 0600 C, Инструкция по эксплуатации

Результаты поиска

Содержание COBRA NC 0600 C

Отзывы:

Похожие инструкции для COBRA NC 0600 C

Бренды по названию

Популярные бренды