background image

7 | Maintenance

18 | 36

Instruction Manual COBRA NC 0500 B_EN_en

7

Maintenance

WARNING

Machines contaminated with hazardous material.
Risk of poisoning!
Risk of infection!

If the machine is contaminated with hazardous material:

Wear appropriate personal protective equipment.

CAUTION

Hot surface.
Risk of burns!

Prior to any action requiring touching the machine, let the machine cool down first.

NOTICE

Using inappropriate cleaners.
Risk of removing safety stickers and protective paint!

Do not use incompatible solvents to clean the machine.

CAUTION

Failing to properly maintain the machine.
Risk of injuries!
Risk of premature failure and loss of efficiency!

Maintenance work must only be executed by qualified personnel.

Respect the maintenance intervals or ask your Busch representative for service.

Shut down the machine and lock against inadvertent start up.

Turn off the water supply.

Vent the connected lines to atmospheric pressure.

If necessary:

Disconnect all connections.

7.1

Draining the Cooling Water

Make sure that the vacuum pump is switched off and cannot accidentally be switched on again.

Put a drain tray underneath the cooling water connections (CWI, CWO).

Disconnect the cooling water connections (CWI, CWO).

Use compressed air to force the remaining cooling water out of the cooling water circuit. Blow in
compressed air into CWI during 30 seconds until it exits dry.

Содержание COBRA NC 0500 B





































Отзывы: