background image

26 

Limited Warranty 

Fire Ring 

Burntech Fireplace Solutions warrants all Burntech manufactured products to be free from defects in materials 
that adversely affect Fire Ring performance for a period of ten (10) years from the date of purchase, subject to the 
terms and conditions of this limited warranty. Burner, 

Valves and electronic parts are only covered for one year, 

parts and labor per the valve manufacturer’s warranty. The manufacturer’s warranty for the electronic ignition and 
valve is for one year. 

 

This warranty covers only products manufactured by Burntech Fireplace Solutions, and NO WARRANTY, EXPRESS 
OR IMPLIED, EXTENDS TO ANY OF THE HARDWARE, FOUNDATION, VENTING, DUCTS, OR ACCESSORIES. THIS 
WARRANTY DOES NOT COVER DRAFTING, SMOKING, OR SOOTING OF THE Burntech Fire Ring. Factors beyond the 
manufacture’s control may affect drafting, smoking, and sooting, Burntech Fireplace Solutions cannot guarantee 
these aspects of performance.  

If a component is found to be defective under the terms of this warranty, the party this warranty is extended to 
shall notify Burntech Fireplace Solutions, 6520 Platt Ave #577 West Hills, CA 91307 in writing, by registered mail, 
within thirty (30) days following the discovery of the defect within the warranty period. The letter shall contain (1) 
the date of the purchase; (2) place of purchase; (3) address of installation; (4) name, address and phone number of 
the homeowner; and (5) a brief description of the defect. 

Burntech Fireplace Solutions, or any entity thereof, is not responsible for any labor costs or indirect costs incurred 
for the replacement of defective components. 

Burntech Fireplace Solutions is not responsible for misuse or mishandling of the component parts. Nothing in this 
warranty makes Burntech Fireplace Solutions, or any entity thereof, liable in any respect for any injury or damage 
to the building or structure in which the Toscana Oven has been installed or to the persons or property therein 
arising out of the use, misuse, or installation of property manufactured Burntech Fireplace Solutions product. 

Burntech Fireplace Solutions, OR ANY ENTITY THEREOF, SHALL NOT BE HELD LIABLE FOR ANY INCENDENTAL OR 
CONSEQUENTIAL DAMAGES OR EXPENSES ARISING OUT OF THE USE OF THE Burntech Fire RIng. ALL DAMAGES 
AND EXPENSES ARE HEREBY EXCLUDED. 

This warranty is null and void when the Fire Rings are not installed pursuant to the installation instructions 
provided by Burntech Fireplace Solutions and local building codes have not been followed completely.

 

 

This warranty applies only to those Fire Rings installed in the continental United States, Hawaii, Alaska and Canada. 
If any part of this warranty is found to be unenforceable, the remaining parts shall remain in force and effect.  

Burntech Fireplace Solutions HEREBY DISACLAIMS ALL GUARANTEES AND WARRANTIES, EXPRESS OR IMPLIED, 
BEYOND THE WARRANTIES SET FORTH HEREIN. 

CUSTOMER SERVICE & PARTS REPLACEMENT: 
Parts and accessories may be purchased from your local dealer. Additional information is available from Burntech 
Fireplace Solutions Accessory orders will be accepted by mail, or you may call to order Monday thru Friday from 
1:00 p.m. to 5:00 p.m. (Pacific Standard Time) at: (818) 564-4253 

Please complete the following information for future reference and warranty verification: 

Date of Purchase ____________________20_____ 

Serial # ____________________ 

Содержание BOFP-48NG



























Отзывы: