Bunn U3A Скачать руководство пользователя страница 15

Страница: 15 / 30

Page 15

SERVICE (cont.)

CONTROL THERMOSTAT

FIG. 4 CONTROL THERMOSTAT

P2178.60

Location:

The control thermostat is mounted on the right

front of the component bracket.

Test Procedures:
1. Disconnect the brewer from the power source.
2. Locate the thermostat and check for 230 volts

between the red wire from the main harness on the
control thermostat and the black wire on the main
terminal block

3. Disconnect the brewer from the power source.

If voltage is present as described, proceed to #4.
If voltage is not present as described, refer to the

wiring diagram and check the brewer wiring harness.

4. Disconnect the red wires from the control thermo-

stat.

5. Check for continuity across the terminals on the

control thermostat with the control thermostat in
the "ON" position (fully clockwise), continuity must
not be present when the thermostat is in the "OFF"
position (fully counterclockwise).

If continuity is present as described, the control ther-

mostat is operating properly.

If continuity is not present as described, replace the

control thermostat.

Removal and Replacement:

1. Disconnect the wires from the control thermostat.
2. Remove the thermostat capillary bulb by firmly

pulling up on the capillary at the component bracket.
This will disengage the grommet from the compo-
nent bracket.

3. Remove the #8-32 screw securing the control

thermostat and mounting bracket to the compo-
nent bracket. Remove control thermostat and
bracket as an assembly.

4. Remove knob from control thermostat.
5. Remove the two #6-32 screws securing the con-

trol thermostat to the thermostat mounting bracket.
Remove and discard thermostat.

6. Install new control thermostat on thermostat

mounting bracket and secure with two #6-32
screws.

7. Install knob on thermostat.
8. Install thermostat and mounting bracket on the

component bracket and secure with one #8-32
screw.

9. Carefully bend the capillary tube so that the tube

and bulb inside the brewer are in the vertical
position with the grommet located 5 1/2 " above
the capillary bulb.

NOTE:

The capillary tube must be clear of any electrical

termination and not kinked.

10. Refer to Fig. 5 and reconnect the wires.
11. Adjust the control thermostat as required.

RED from Main
Harness

RED to Limit Thermostat

FIG. 5 CONTROL THERMOSTAT TERMINALS

P1730

10060.3 070102

Содержание U3A































Результаты поиска

Содержание U3A

Отзывы:

Бренды по названию

Популярные бренды

Bunn U3A, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание U3A

Отзывы:

Бренды по названию

Популярные бренды