Bunn H5M Скачать руководство пользователя страница 5

Страница: 5 / 20

INITIAL SET-UP

CAUTION -

The dispenser must be disconnected from the power source

throughout the initial set-up, except when specified in the instructions.

Remove the upper rear panel and rotate the control thermostat knob

fully counterclockwise to the “OFF” position and replace the panel.

Connect the dispenser to the power source and turn-on the water

supply.

Water will automatically flow into the tank to the proper level and

shut-off. This will take approximately 10 minutes.

Disconnect the dispenser from the power source, remove the upper

rear panel and place the control thermostat knob fully clockwise to

the “ON” position, and replace the panel.

Connect the dispenser to the power source and wait approximately

twenty minutes for the water in the tank to heat.

On models with ready indicator, the indicator will glow when the

proper water temperature for use is achieved.

P1781

Plumbing Hook-Up

1. Flush the water line and securely attach it to the flare fitting on

the rear of the dispenser.

2. Turn-on the water supply.

10267 101507

P1770

DRAINING THE DISPENSER

CAUTION -

The dispenser must be disconnected from the power source throughout these steps.

1. Disconnect the dispenser from the power source.

2. Shut-off and disconnect the incoming water supply

3. Remove the 4-40 screws at the sides of the top panel.

4. Gently remove one of the grommets from the tank lid.

5. Insert a tube to the bottom of the tank and syphon ALL of the water out. Bunn-O-Matic has a syphon assembly avail-

able (#12440.0000) for this purpose.

NOTE -

The dispenser must be full using the INITIAL SET-UP steps before reconnecting to the power source.

CLEANING

The use of a damp cloth rinsed in any mild, non-abrasive, liquid detergent is recommended for cleaning all surfaces

on Bunn-O-Matic equipment.

WALL MOUNTED INSTALLATION

If the dispenser is wall mounted, the bottom of the dispenser should be at the same height as a counter or table top.

Use B.O.M. part #12542.0000 for side mounted Wall Bracket Kit or # 13125.0001 for front mounted Wall Bracket Kit .

SUPPORT FOR LARGE RECEPTACLES

CAUTION:

If the dispenser is to be used with larger receptacles such as pitchers or pots, those receptacles must be

adequately supported during dispensing of hot water to avoid spillage of very hot water. This support may be provided by

a table or counter top, or use B.O.M. part #12599.0000 Shelf Kit

Содержание H5M





















Результаты поиска

Содержание H5M

Отзывы:

Похожие инструкции для H5M

Бренды по названию

Популярные бренды

Bunn H5M, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание H5M

Отзывы:

Похожие инструкции для H5M

Бренды по названию

Популярные бренды