background image

3

INTRODUCTION

This equipment dispenses hot beverages or soup on demand from powdered product.  It has three hoppers.  

This equipment may also dispense cold beverages from powdered product from the left dispense station.  It is 

for indoor use only on a sturdy counter or shelf.

00831.0000

28301.0003

WARNING

!

Fill water tank before turning - on - 

thermostat or connecting appliance

to power source.

Use only on a properly protected

circuit capable of the rated load.

Electrically ground the chassis.

Follow national/local electrical codes.

Do not use near combustibles.

FAILURE TO COMPLY RISKS EQUIPMENT

DAMAGE, FIRE, OR SHOCK HAZARD

READ THE ENTIRE OPERATING MANUAL

BEFORE BUYING OR USING THIS PRODUCT

THIS APPLIANCE IS HEATED WHENEVER

CONNECTED TO A POWER SOURCE

00831.0000F  3/98   ©1998  BUNN-O-MATIC CORPORATION 

28328.0000

190

°

160

°

HEATER

TEMPERATURE

ADJUSTMENT

26527.0003

THERMOSTAT ASSEMBLY

120VAC

BUNN-O-MATIC CORP

Artwork for P/N: 26536.0003 
Artwork Rev:  A
Drawn:  REF
Date:  03/16/09

ELECTRONIC THERMOSTAT

26536.0003

USER NOTICES

Carefully read and follow all notices on the equipment and in this manual.  They were written for your protection. 

All notices are to be kept in good condition.  Replace any unreadable or damaged labels.

29170 051111

28368.0004

CONTROL THERMOSTAT ADJUSTMENT

APPROXIMATE  THERMOSTAT  TEMPERATURE  SETTINGS

200 F

190 F

180 F

28368.0004A  08/08  

©  

2008 BUNN-O-MATIC CORPORATION

OFF

OFF

OFF

HI

HI

HI

BUNN

BUNN

BUNN

37881.0000

00656.0001

As directed in the International Plumbing Code of the 

International  Code  Council  and  the  Food  Code 

Manual of the Food and Drug Administration (FDA), 

this  equipment  must  be  installed  with  adequate 

backflow  prevention  to  comply  with  federal,  state 

and  local  codes.  For  models  installed  outside  the 

U.S.A., you must comply with the applicable Plumb-

ing /Sanitation Code for your area.

Artwork for P/N:  00656.0001
Artwork Rev:  A
Drawn:  REF
Date:  04/22/10

00824.0002

Содержание FMD-3










Отзывы: