manualshive.com logo in svg

Bunn CWT TWIN, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
Bunn CWT TWIN Скачать руководство пользователя страница 25

Page 25

SERVICE (cont.)

10737 120800

DIGITAL BREW TIMER (Late Models)

P2197

FIG. 21 DIGITAL BREW TIMER

Location:

The timers are located inside the front of the trunk

on the upper right side of the component brackets.

Test Procedure.

NOTE: 

Do not remove or install wires while timer board

is installed. Pressure applied to one side may cause
damage to the board.
1. Disconnect the brewer from the power source and

remove the front access panel.

2. Remove  the  one  #8-32  screw  securing  circuit

board to the mounting bracket.

3. Remove circuit board and spacers (as required).
4. With a voltmeter, check the voltage across termi-

nals TL1 and TL2 when the "ON/OFF" switch is in
the "ON" position. Connect the brewer to the power
source. The indication must be:
a) 120 volts ac for three wire 120/240 volt models.
b) 200 volts ac for two wire 200 volt models.
c) 240 volts ac for two wire 240 volt models.
d) 230 volts ac for three wire three phase 230 volt
models.

5. Disconnect the brewer from the power source.

If voltage is present as described, proceed to #6.
If  voltage  is  not  present  as  described,  refer  to  the
Wiring  Diagrams  and  check  the  brewer  wiring  har-
ness.

6. With a voltmeter, check the voltage across termi-

nals TL1 and TL4 when the "ON/OFF" switch is in
the "ON" position. Connect the brewer to the power
source. The indication must be 0 volts.

If voltage is as described, proceed to #7.
If voltage is not as described, disconnect the brewer
from the power source and replace the timer.

7. With a voltmeter, check the voltage across termi-

nals TL1 and TL4 when the "ON/OFF" switch is in
the "ON" position. Connect the brewer to the power
source and press the "START" switch. The indica-
tion must be as follows:
a) 120 volts ac for three wire 120/240 volt models.
b) 200 volts ac for two wire 200 volt models.
c) 240 volts ac for two wire 240 volt models.
d) 230 volts ac for three wire three phase 230 volt
models.

If voltage is present as described, the brew timer is
operating  properly.  Reset  the  timer  as  required,  to
obtain the desired brew volume.
If voltage is not present as described, disconnect the
brewer from the power source and replace the timer.

Removal and Replacement:
1. Remove  the  one  #8-32  screw  securing  circuit

board to the mounting bracket.

2. Remove circuit board and spacers (as required).
3. Remove all wires from the timer.
4. Attach  all  wires  to  the  replacement  timer  board

prior to installation to the component mounting
bracket.  Refer to Fig. 22 when reconnecting the
wires.

5. Install  new  circuit  board  with  spacers  (as  re-

quired) to the component mounting bracket. The
tapered spacer should locate over the pin.

6. Adjust the timer as described below.

Timer Setting:

NOTE: 

Prior to setting or modifying volumes, check

that the brewer is connected to water supply, the tank
is properly filled, and a funnel and server are in place.

NOTE: 

All  volume  settings  must  be  done  with  the

sprayhead installed.

Содержание CWT TWIN



































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды