background image

3

28791 071411

INTRODUCTION

This equipment supplies a liquid concentrate mixed with water at various ratios to the  hoppers on the dispens-

ers.  It is for indoor use only on a sturdy counter or shelf.

USER NOTICES

Carefully read and follow all notices on the equipment and in this manual.  They were written for your protection. 

All notices are to be kept in good condition.  Replace any unreadable or damaged labels.

00656.0001

00986.0002

As directed in the International Plumbing Code of the 

International Code Council and the Food Code 

Manual of the Food and Drug Administration (FDA), 

this equipment must be installed with adequate 

backflow prevention to comply with federal, state 

and local codes. For models installed outside the 

U.S.A., you must comply with the applicable Plumb-

ing /Sanitation Code for your area.

Artwork for P/N:  00656.0001
Artwork Rev:  A
Drawn:  REF
Date:  04/22/10

37881.0000

ELECTRICAL REQUIREMENTS

CAUTION - The dispenser must be disconnected from the power source until specified in Initial Set-Up.

The 120 volt version of this dispenser has an attached cordset and requires 2-wire, grounded service rated 120 

volts ac, 15 amp, single phase, 60 Hz.  The mating connector must be a NEMA 5-15R.

The 230 volt CE version requires 2 wire, grounded service rated 230V ac, single phase, 50 Hz.

The 200 volt or 240 volt versions require 2 wire, grounded service rated 200 volts ac or 240 volts ac, single 

phase, 50 Hz.

(Refer to the dispenser’s data plate for exact voltage requirement.)

00824.0002

CE REQUIREMENTS

• This appliance must be installed in locations where it can be overseen by trained personnel.

• For proper operation, this appliance must be installed where the temperature is between 5°C to 35°C.

• Appliance shall not be tilted more than 10° for safe operation.

• An electrician must provide electrical service as specified in conformance with all local and national codes.

• This appliance must not be cleaned by water jet.

• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental 

capabilities, or lack of experience and knowledge, unless they have been given instructions concerning use of 

this appliance by a person responsible for its safety.

• Children should be supervised to ensure they do not play with the appliance.

• If the power cord is ever damaged, it must be replaced by the manufacturer or authorized service personnel 

with a special cord available from the manufacturer or its authorized service personnel in order to avoid a hazard.

• Machine must not be immersed for cleaning.

Содержание AFPO-2









Отзывы: