BullFrog 2002 Spas Скачать руководство пользователя страница 19

Страница: 19 / 42

Page 19

Bullfrog Spas Owner’s Manual

Standby

Pressing “Standby” will turn off all spa functions tem-

porarily. This is helpful when changing out a JetPak™ or

a filter cartridge. Pressing any button resets the spa.

Option

The “Option” button is used to operate any equipment

added to spa. Follow manufacturer’s instructions.

Aux

The “Aux” button is used to operate any equipment

added to spa. Follow manufacturer’s instructions.

Mode/Prog

This button is used to switch between standard, econ-

omy, and sleep modes. Press “Mode/Prog” to select

desired mode (LCD flashes until confirmed), then press

“Cool” to confirm selection.

Standard Mode

is programmed to maintain the desired

temperature. Note that the last measured spa

temperature displayed is current only when the circ

pump has been running for at least 2 minutes. The
“

STANDARD

” icon will display until the mode is

changed.

Economy Mode

heats the spa to set temperature only

during filter cycles. The “

ECONOMY

” icon will display

until mode is changed.

Push “Jets 1” to shift to Standard-in-Economy Mode,
indicated by

“SE”

alternating with the temperature. The

spa operates the same as it does in Standard Mode, but

reverts to Economy Mode automatically after 2 hours.

During this time, a press of the “Mode” button will

revert to Economy Mode immediately.

Note:

Heating will occur more quickly in Standard-in-

Economy Mode if a low-speed (versus a high speed)

pump is operating.

Sleep Mode

heats the spa to within 20°F of the set

temperature only during filter cycles. The “

SLEEP

” icon

will display until mode is changed.

Preset Filter Cycles

There are two filter cycles per day. The start/end times

of each cycle are programmable. To program start/end

times, continue following prompts after setting time as

instructed above, pressing “Mode/Prog” to advance to

the next setting (or to exit after the last setting). The

default filter cycles are as follows: The

first filter cycle

is automatically activated at 8:00 AM and operates the

low speed of pump 1 until 10:00 AM. The LCD above

the “Time” button will light when filter 1 is running. The

second filter cycle

is automatically activated at 8:00

PM and operates the low speed of pump 1 until 10:00

PM. The LCD above the “Mode/Prog” button will light

when filter 2 is running.

The low speed of pump 1 and the ozone generator (if

installed) will run during filtration. At the start of each

filter cycle, the high speed of pump 2 will run for 5

minutes.

Wiring Diagram: Limited Control System

Содержание 2002 Spas











































Результаты поиска

Содержание 2002 Spas

Отзывы:

Бренды по названию

Популярные бренды

BullFrog 2002 Spas, Руководство пользователя

Результаты поиска

Содержание 2002 Spas

Отзывы:

Бренды по названию

Популярные бренды