background image

SYSTEM FEATURES

SYSTEM COMPONENTS

TECHNICAL ASSISTANCE

Should you need help. First check our website at www.bulldogsecurity.com/wires.htm or call our toll-free

Tech Support Hotline Monday through Friday 9AM-8PM and Saturday 10AM-4PM EST at 800-878-8007.

You must give the following information:

Name

•Telephone Number with Area Code (Fax number if applicable)

•Year, Make, and Model of the vehicle

•The model number of the system you are installing

•The type of assistance you are requesting

If you give the above information you will be called back as soon as possible, usually within 10 minutes.

BEFORE YOU BEGIN

1

REQUIRED TOOLS

Two-Button Extended Range

Remotely start your car to run the heater or air conditioning from an extended distance.

Remote Control

Parking Light Confirmation

signal and will remain on if the engine is remotely Confirms that your vehicle has received a

remote signal and will remain on if the engine is remotely started. (Optional part #775 required.)

Code Learning

Allows your remote starter to learn new remotes, should you want to add remotes, or if remotes

are lost.

Pre Programmed Run Time

Unit is programmed to run for 15 minutes or stop at any time with the remote or by depressing

the brake.

Pit Stop Mode

Allows you to exit the vehicle while the engine remains running.

Tach/Tachless Option

A programmable feature that lets you decide to choose the easy to install tachless operation

or the standard wire-in, tach operation.

Limited Lifetime Warranty

Guarantees life-long protection.

Your system includes:

Installation & Operation Guide

1-Main Control Module

1- Two Button Remote Transmitter

1- 11-Pin Wire Harness

You will need a sharp knife, electrical tape and a computer-friendly test light, a 5/16 inch drill bit

to install the hood pin switch. If the bottom of your dash on the driver’s side will come off, you must

remove it. If this is the case a screwdriver or a socket set may be needed,

1-3-Pin 4-Relay Harness

1-Hood Pin Switch

1-Warranty

1-Warning Sticker for Under the Hood

Congratulations, you have purchased one of the most advanced remote starter systems ever made. Your new remote

starter is a technological breakthrough utilizing the most advanced, state of the art technology and components.

It is computer controlled and manufactured in the U.S.A. The dependability and variety of features make Bulldog

Security the leader in the industry. Enjoy your new remote starter for years to come!

This remote system is designed to start your vehicle by sending a command signal from the remote transmitter.

It is required that your installation is done in a well-ventilated area. It is the responsibility of the

owner to ensure that the remote system is not used to start the vehicle in an undesired location.

It is recommended that a carbon monoxide detector be installed in the living area near a location where the

vehicle may be garaged.

Содержание RS82









Отзывы: