Bull Cedoc Bull Escala 2104 TS4 Скачать руководство пользователя страница 68

Страница: 68 / 87

One RAID adapter in each of two non-HACMP host systems
connected to two 2104 Model TS4s

Figure 42 shows one RAID adapter in each of two non-HACMP host systems
connected to two 2104 Model TS4s (dual-bus mode).

SCSI interface card.

SCSI RAID adapter:

PCI 4-Channel Ultra3 SCSI RAID Adapter (type number 4-X, feature code 2498)

PCI-X Dual Channel Ultra320 SCSI RAID Adapter (type number 5703, feature
code 5703)

Important:

An RS/6000 or IBM

Eserver

pSeries computer running Linux for

pSeries uses the following to connect to the 2104 Model TS4.

PCI-X Dual Channel Ultra320 SCSI RAID Adapter (type number 5703, feature
code 5703)

Notes:

1. The SCSI address of the adapter that is connected to the 2104 Model TS4 must

be different from the addresses of the installed disk drive modules.

2. The external connectors on the SCSI RAID adapter cards and the internal RAID

connector must not share a SCSI bus.

2104 Subsystem

Host System

Figure 42. One RAID adapter in each of two non-HACMP host systems connected to two
2104 Model TS4s (dual-bus mode)

2104 Model TS4 Installation Guide

Содержание Bull Escala 2104 TS4
























































































Результаты поиска

Содержание Bull Escala 2104 TS4

Отзывы:

Похожие инструкции для Bull Escala 2104 TS4

Бренды по названию

Популярные бренды

Bull Cedoc Bull Escala 2104 TS4, Руководство по установке

Результаты поиска

Содержание Bull Escala 2104 TS4

Отзывы:

Похожие инструкции для Bull Escala 2104 TS4

Бренды по названию

Популярные бренды