Buffalo TeraStation 6000 Series Скачать руководство пользователя страница 67 | Manualshive

Страница: 67 / 226

background image

3

Right-click the drive volume that shows the status “Unallocated” and click

New Simple Volume

from the

displayed menu. Follow the screen to finish formatting.

When the formatting process is completed, the drive will be visible as an icon in Computer or This PC and can be
used as a normal drive on the computer.

Disconnecting a Volume

1

From Windows, navigate to

Control Panel

>

System and Security

>

Administrative Tools

>

iSCSI Initiator

.

The status of the connecting volume will be displayed as “Connected” under “Discovered targets”.

2

Select a volume to disconnect and click

Disconnect

.

3

Click

Yes

.

4

When the volume status is displayed as “Inactive”, the disconnection was carried out properly.

Using with Multiple Computers

If the TeraStation is divided into multiple volumes (or drives), it can be used with multiple computers. However, it is
not recommended to access a single volume or drive from multiple computers at the same time for security reasons.

When using the TeraStation as an iSCSI device, it should only connect to a single initiator unless the computer
running the initiator also has clustering enabled and configured on its operating system. To avoid using multiple
initiators for access, enable mutual authentication.

Checking Whether iSCSI Volume Is Connected

To check whether an iSCSI volume is connected, navigate to

Storage

>

iSCSI

. Current volumes will be listed. If

“Connected” is displayed under “Status”, the volume is currently connected to the client.

Configuring Access Restrictions

A CHAP name and secret can be configured for the entire iSCSI volume or each existing volume. Access restrictions
can be configured so that entering a target CHAP name and secret is required for each connection.
The TeraStation can perform mutual authentication (two-way authentication). Dual passwords ensure that only
authorized client computers can access the volume on the TeraStation.
Follow the procedure below to enable access restrictions.

Configuring Access Restrictions for the Entire TeraStation

1

From Settings, click

Storage

.

2

Click the settings icon (

) to the right of “iSCSI”.

66

Chapter 4 Storage Management

«
...
65
66
67
68
69
...
»

Содержание TeraStation 6000 Series



































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TeraStation 6000 Series

Бренд: Eastwood Страницы: 8

Бренд: SanDisk Страницы: 4

Бренд: TrekStor Страницы: 100

Бренд: U-Line Страницы: 5

Бренд: Patiowell Страницы: 27

Бренд: Onnto Страницы: 40

Бренд: Seagate Страницы: 68

Бренд: QNAP Страницы: 7

Rotate FlashPen

Бренд: Hama Страницы: 4

Бренд: ST Страницы: 9

NXA-WC80211G-CF

Бренд: AMX Страницы: 6

1 GB Microdrive Storage Card

Бренд: IBM Страницы: 2

Бренд: AIC Страницы: 79

Бренд: Spectra Logic Страницы: 15

Бренд: Metro DataVac Страницы: 16

HTS723212L9A360

Бренд: Hitachi Страницы: 176

HTS723212L9A360

Бренд: Hitachi Страницы: 5

Бренд: HP Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды