background image

 

 

Item # MOTOR25

  

INSTRUCTION MANUAL

 

 

 

READ  ALL  INS TRUCT IO NS AND  WARN INGS  BE FORE  U SE  

 

This  manual  provides  important  information  on  operation  &  maintenance.  These  instructions  are  not  meant  to  cover  every 

possible condition and situation that may occur. We reserve the right to change this product at any time without prior notice. 
F O R  C O N S U M ER  U S E  O N L Y   –   N O T  F O R  P R O F E SS IO N A L  U S E.  

IF TH ERE  I S  ANY QU ES TION A BOUT  A  COND I T ION BE ING  SAFE  OR  
UNSAFE,  DO  NOT  OP ER AT E  THI S  PRODUCT !    
 
HAVE  QUESTIONS  OR  PROBLEMS?  CONTACT  CUSTOMER  SERVICE 

 

If you experience a problem, have questions or need parts for this product, call Customer Service at 

1-866-460-9436,  

M o n d a y - F rid a y, 8  A M   -   4  P M   C e n tra l T im e

. A copy of the sales receipt is required. 

 
KEEP   THIS  MANUAL ,  S ALES  RE CEI P T &  AP PLICABLE  WAR RANT Y FO R 
FUTURE  REF ERENC E .    

Keep this manual onboard in a waterproof bag when boating. The manual should stay  with the outboard motor if sold

.  

2 YEAR LIMITED EMISSION-RELATED WARRANTY  

 

THIS ENGINE MEETS U.S. EPA EMISSION STANDARDS UNDER 40 CFR 1054.625 .The emission-related limited warranty is 

valid for two (2) years. Keep the purchase receipt and mail in the product registration card for proof of purchase. Buffalo Corp 
limits emission-related warranty repairs to authorized service centers for owners located within 100 miles of an authorized 

service center. For owners located more than 100 miles from an authorized service center, Buffalo Corp will, in its sole discretion, 
either pay for shipping costs to and from an authorized service center, provide for a service technician to come to the owner to 

make the warranty repair, or pay for the repair to be made at a local non-authorized service center. The provisions of this 
paragraph apply only for the contiguous states, excluding the states with high-altitude areas identified in 40 CFR part 1068, 

Appendix III. 

 

To exercise this warranty, DO NOT RETURN TO RETAILER. Instead, call Customer Service toll free at 1-866-460-9436 (email 
address [email protected]) and you will be instructed on where to take the engine for warranty service. Take the engine and 

proof of purchase (your receipt) to the repair facility recommended by the Customer Service Representative. The warranty does 
not extend to products damaged or affected by fuel contamination, accidents, neglect, misuse, unauthorized alterations, use in 

an application for which the product was not designed and any other modifications or abuse.  

 

1 YEAR LIMITED WARRANTY  (30 Day Limited Warranty for Commercial and Rental Purpose) 

 

Engines are warranted to be free from defects in materials and workmanship for a period of 1 YEAR from date of original 
purchase. Buffalo Corp. is not liable for any indirect, incidental or consequential damages from the sale or use of this product. 

Any implied warranties are limited to 1 YEAR as stated, or as otherwise stated, in this written limited warranty. Some states do 
not allow the exclusion or limitation of incidental or consequential damages. Some states do not allow limitation on the length of 

an implied warranty. Buffalo Corp will repair or replace, at its discretion, any part that is proven to be defective in materials or 
workmanship under normal use during the 1 YEAR warranty period. Warranty repairs or replacements will be made without 

charge for parts or labor. Parts replaced during warranty repairs will be considered as part of the original product and will have 
the same warranty period as the original product. This warranty gives you specific legal rights, and you may have other rights 

that vary state to state.

 

   

 

0201310

 

 

ATTENTION: FOLLOW ENGINE BREAK-IN PROCEDURE FOR 

FIRST 20 HOURS OF USE. 

PA 

 

ATTENTION: OIL AND GASOLINE IS NOT INCLUDED WITH 

THE MOTOR AND MUST BE ADDED BEFORE FIRST USE. 

 

Содержание MOTOR25

















































Отзывы: