Buell XB 2010 Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 714

background image

1.13

INTERACTIVE EXHAUST CABLE

ADJUSTMENT

1.

Remove intake cover assembly. See

NOTES

•

The actuator cover used on models with translucid body
panels does not need to be removed in order to adjust
cable.

•

When the ignition/light switch is turned off with the inter-
active exhaust valve in motion, the valve will stop partially
open which will cause an inaccurate adjustment. For a
description of the inactive exhaust operation, see

6.16 INTERACTIVE EXHAUST SYSTEM

.

2.

To close the valve in the muffler, cycle the actuator:

a.

Hold the throttle wide open.

b.

Turn the engine cut-off switch to RUN.

c.

Turn the ignition/light key switch ON.

d.

Watch the actuator cycle close/open/close.

3.

. Loosen jam nut (3).

4.

Remove cable (2) from bracket and cable wheel (4).

NOTE

For the next step in the procedure it will be necessary to obtain
a permanent marker.

5.

Using a pair of pliers, fully open the exhaust valve in the
muffler by pulling the cable core by the ferrule that was
disconnected from the cable wheel in the previous step
until resistance is felt. Be careful not to damage the cable
core.

6.

Mark the cable core with the marker all the way around
where it comes out of the housing.

7.

Release the cable core and reattach the cable to the cable
wheel and bracket.

8.

Tighten jam nut.

NOTE

Do not overtighten jam nut on interactive exhaust cable.

9.

See

. Adjust interactive exhaust cable as fol-

lows:

a.

Move cable with your fingers from side to side. There
should be no more than 1/8 in. (3.2 mm) side play in
cable in either direction with 1/4 in. (6.4 mm) max-
imum overall side play.

b.

See

. Adjust cable as needed using cable

adjuster (1).

NOTES

•

In this mode the exhaust valve in the interactive muffler
should cycle from the closed position to the wide open
position and back to the closed. When the exhaust valve
moves to the open position, you should see the mark on
the cable core made previously. This verifies the system

is working properly. If you do not see the mark, verify
previous cable adjustment.

•

DO NOT start vehicle in this mode.

10. Cycle the actuator to verify cable and valve operation:

a.

Hold the throttle wide open.

b.

Turn the engine cut-off switch to RUN.

c.

Turn the ignition/light key switch ON.

d.

Watch the actuator cycle close/open/close.

11. See

. Verify that the interactive exhaust cable

(1) is routed behind the frame lug (2) before installing air
intake cover.

NOTE

If cable is routed in front of the frame lug it will cause the muffler
valve to stay open not allowing it to work properly.

12. Install air intake cover. See

2.38 INTAKE COVER

4

3

2

1

sm00504

1.

Adjuster

2.

Interactive exhaust cable

3.

Jam nut

4.

Cable wheel

Figure 1-26. Interactive Exhaust Cable

1-28 2010 XB Service: Maintenance

«
...
48
49
50
51
52
...
»

Содержание XB 2010











































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для XB 2010

Бренд: Yamaha Страницы: 94

Бренд: Yamaha Страницы: 44

Бренд: Öhlins Страницы: 8

Бренд: R&G Страницы: 12

Бренд: Yoshimura Страницы: 7

Бренд: IRC Страницы: 2

Light Bee QL3000DY

Бренд: Surron Страницы: 18

Бренд: dushi Страницы: 4

Бренд: DYNATEK Страницы: 4

Бренд: DYNATEK Страницы: 6

Бренд: GAS GAS Страницы: 52

TXT RACING 2015

Бренд: GAS GAS Страницы: 59

Бренд: GAS GAS Страницы: 56

Бренд: GAS GAS Страницы: 128

Бренд: GAS GAS Страницы: 131

Бренд: KOOFU Страницы: 24

Бренд: Peugeot Motorcycles Страницы: 50

Бренд: Bell Sports Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды