Buell XB 2010 Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 714

background image

Do not overfill the primary chaincase with lubricant.
Overfilling can cause rough clutch engagement, incom-
plete disengagement, clutch drag and/or difficulty in
finding neutral at engine idle. (00199b)

6.

Make certain primary chaincase is filled with proper
amount of lubricant with motorcycle upright. If under filled,
transmission can be damaged during vehicle operation.

7.

. Add GENUINE HARLEY-DAVIDSON

TRANSMISSION AND PRIMARY CHAIN-
CASE LUBRICANT (Part No. 99851-05, quart size) as
required until fluid level is even with bottom of clutch dia-
phragm spring.

NOTE

Each time the clutch inspection cover is removed, the gasket
must be replaced.

8.

Install new clutch cover gasket.

9.

See

. Install clutch inspection cover tightening

three fasteners and washers to 84-108 in-lbs (9.5-12.2
Nm).

10. Clean up any fluid that may have spilled on muffler.

sm00089

Figure 1-16. Clutch Inspection Cover (Typical)

sm05323

Figure 1-17. Primary Drain Plug: XB Models

ADJUSTMENT

If clutch slips under load or drags when released, first check
control cable adjustment. If cable adjustment is within specific-
ations, adjust clutch mechanism as described below.

When necessary, lubricate cable with Harley Lube (Part No.
HD-94968-09).

1.

Position the vehicle upright and level. This will prevent
lubricant from draining out when clutch inspection cover
is removed.

2.

See

. Slide rubber boot (1) upward to expose

adjuster mechanism. Loosen jam nut (3) from adjuster (4).
Turn adjuster to shorten cable housing until there is a large
amount of free play at clutch hand lever.

3.

. Remove three fasteners and washers

from clutch inspection cover. Remove clutch inspection
cover and gasket from primary cover.

4.

See

. Remove spring (1) and lockplate (2).

Using a flat tip screwdriver, turn adjusting screw (3)
counterclockwise until it lightly bottoms.

5.

Turn adjusting screw clockwise 1/4-1/2 turn. Install lock-
plate and spring on adjusting screw flats. If hex on lock-
plate does not align with recess in outer ramp, rotate
adjusting screw clockwise until it aligns.

NOTES

•

All Ulysses models now incorporate a hook for the clutch
cable into the handlebar assembly. The purpose of this
hook is to control the routing of the clutch cable so it will
not interfere with the instrument cluster mounted to the
front of the upper fork clamp.

•

All cable adjustments for the Ulysses models are to be
performed with the clutch cable free from the handlebar

1-20 2010 XB Service: Maintenance

«
...
40
41
42
43
44
...
»

Содержание XB 2010











































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для XB 2010

Бренд: Kabuto Страницы: 12

Бренд: hepco & becker Страницы: 6

Бренд: CF MOTO Страницы: 443

Бренд: R&G Страницы: 6

Бренд: Honda Страницы: 150

Бренд: Caberg Страницы: 16

Бренд: National Cycle Страницы: 2

Бренд: Suzuki Страницы: 101

Бренд: Ericsson Страницы: 44

Бренд: hepco & becker Страницы: 2

Бренд: hepco & becker Страницы: 3

Бренд: Kinroad Страницы: 26

Can-Am Spyder RT

Бренд: F4Customs Страницы: 3

RetroRadio BT100

Бренд: Biketronics Страницы: 2

Бренд: KTM Страницы: 26

Бренд: KTM Страницы: 32

Бренд: iCO Racing Страницы: 12

Бренд: Zero Страницы: 154

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды