Buell XB 2010 Скачать руководство пользователя страница 190 | Manualshive

Страница: 190 / 714

background image

2.24

THROTTLE CONTROL

REMOVAL AND DISASSEMBLY

1.

Remove right handlebar deflector if required. See

2.28 DEFLECTORS

NOTE

On Ulysses models, it will be necessary to disconnect and
remove the heated handgrips. See

6.11 HEATED HAND

GRIPS: ULYSSES MODELS

.

2.

. Loosen cable adjuster lock (thick disc)

(2) on each cable.

3.

Turn adjusters (3) in direction which will shorten cable
housings to minimum length.

4.

Remove fasteners (1) on right switch housing and separate
housing from handlebar.

5.

See

. Remove cables (2, 3) from notches in

front housing (4).

6.

Remove cables (2, 3) and ferrules (6) from cable wheel
(7).

1

2

5

4

3

sm00596

1.

Right switch housing fasteners (top fastener
above brake lever)

2.

Cable adjuster lock

3.

Adjusters

4.

Throttle control cable

5.

Idle control cable

Figure 2-149. Throttle Control Cables

7

1

8

2

5

4

9

6

3

sm00597

1.

Screw (short, top)

2.

Idle control cable

3.

Throttle control cable with molded end

4.

Front housing

5.

Screw (long, bottom)

6.

Ferrules

7.

Cable wheel

8.

Rear housing

9.

Locating pin

Figure 2-150. Cable Connections

CLEANING AND INSPECTION

Compressed air can pierce the skin and flying debris from
compressed air could cause serious eye injury. Wear
safety glasses when working with compressed air. Never
use your hand to check for air leaks or to determine air
flow rates. (00061a)

Clean all parts except cables in a non-flammable cleaning
solvent. Blow dry with compressed air. Replace cables if frayed,
kinked or bent.

ASSEMBLY AND INSTALLATION

1.

Install throttle grip and position ferrules into cable wheel.

2.

Insert idle control into front switch housing.

3.

Slide switch housing over throttle.

4.

Insert throttle cable into front switch housing.

5.

Attach rear switch housing and position housings on right
handlebar by engaging locating pin on front housing with
hole in handlebar. Attach housings with two fasteners,
installing longer fastener on bottom. Tighten to 25-33 in-
lbs (3-4 Nm).

6.

Adjust cables. See

1.12 THROTTLE CABLE

7.

Install right handlebar deflector if removed. See

2.28 DEFLECTORS

.

2-110 2010 XB Service: Chassis

«
...
188
189
190
191
192
...
»

Содержание XB 2010











































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для XB 2010

Бренд: Xenith Страницы: 17

Бренд: Takegawa Страницы: 2

HIGHSIDER VICTORY

Бренд: Paaschburg & Wunderlich Страницы: 5

Бренд: hepco & becker Страницы: 3

Бренд: Xenith Страницы: 7

Бренд: Power Fist Страницы: 12

Бренд: Enerwatt Страницы: 26

Бренд: X-PRO Страницы: 3

Бренд: X-PRO Страницы: 3

Бренд: RIEJU Страницы: 148

Бренд: RIEJU Страницы: 162

SHERCO 250-300 SE/R

Бренд: DEFYGRAVITY Страницы: 67

RR 2T ENDURO 2013 250

Бренд: Beta Страницы: 58

Бренд: Knight Страницы: 19

PEGASO 650 TRAIL

Бренд: APRILIA Страницы: 12

Бренд: hepco & becker Страницы: 5

Бренд: hepco & becker Страницы: 6

Бренд: hepco & becker Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды