manualshive.com logo in svg

Buderus 500 - 24/S, Инструкция по установке и обслуживанию

Поделиться
Скачать
Buderus 500 - 24/S Скачать руководство пользователя страница 21

Installation

1

Installation and maintenance instructions for Buderus 500 - 24/S • 08/2006

21

Subject to modifications resulting from technical improvements!

Buderus • http://www.buderus-domestic.co.uk

1.8

Electrical connections

1.8.1

Mains connection

A mains supply of 230 V - 50Hz is required.

External controls are suitable for volt free or 230 V installation.

Wiring to the boiler MUST be in accordance with the current 
I.E.E. (

BS.7671

) Wiring Regulations and any local regulations.

Wiring should be a 3 core PVC insulated cable, not less than 
0.75 mm

2

 (24 x 0.2 mm), and to table 16 of 

BS.6500

.

Connection must be made in a way that allows complete isola-
tion of the electrical supply such as a double pole switch 
having 3 mm contact separation in both poles, or by a three pin 
connector, serving only the boiler and system controls. This 
boiler is equipped with a double pole switch see fig. 24, item 1.
The means of isolation must be accessible to the user after 
installation.

The electrical connection to the mains supply should be readily 
accessible and adjacent to the boiler.

If the supply cord is damaged, it must be replaced by a regis-
tered Corgi installer to avoid a hazard and must be an original 
spare part.

The electrical supply for both the boiler and the system must 
be taken from the same fused spur outlet.

1.9

DBA wiring diagram

fig. 24 DBA

ON

OFF

1

NOTE

All  Buderus boilers require a 
permanent live.

WARNING!

Do not connect 230V to the connection block 
on the back of the DBA.

DBA

Low voltage

High voltage

JP3

JP4

JP2

JP1

pin 6

pin 1

pin 1

pin 4

pin 1

pin 1

pin 17

pin 17

JP1

JP2

JP4

JP3

WARNING!

Do not connect 230V to the connection block on the back of the DBA.

Содержание 500 - 24/S

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды